Keithley 7012-C Instruction Manual Download Page 9

Page: 9 / 93

MODEL 7012-S

10 Matrix with Screw Terminals.

MODEL 7012-C

10 Matrix with Mass Terminated Connector.

MATRIX CONFIGURATION:

4 rows by 10 columns. Jumpers can be

removed to isolate any row from the backplane.

CONTACT CONFIGURATION:

2-pole Form A (Hi, Lo).

CONNECTOR TYPE:

7012-S

: Screw terminal, #16AWG maximum wire size, with .092 inch

O.D. 28 Conductors maximum. #22AWG typical wire size
with .062 inch O.D. 88 Conductor maximum.

7012-C:

96-Pin male Euro card connector. Mates to female twisted wire
cable, crimp or solder connector.

MAXIMUM SIGNAL LEVEL:

DC Signals:

110V DC between any two pins, 1A switched. 30VA
(resistive load).

AC Signals:

125V RMS or 175V AC peak, between any two pins,
1A switched, 60VA (resistive load).

COMMON MODE VOLTAGE:

175V peak, any pin to chassis.

CONTACT LIFE:

Cold Switching:

closures.

At Maximum Signal Levels:

closures.

CHANNEL RESISTANCE (per conductor):

< 1

Ω

CONTACT POTENTIAL:

7012-S:

< 500 nV per contact pair (Hi, Lo).
< 1.5

V per single contact.

7012-C:

< 1

V per contact pair (Hi, Lo).

< 3

V per single contact.

OFFSET CURRENT:

< 100 pA.

ACTUATION TIME:

3 ms.

ISOLATION:

Path:

>10

Ω

, < 50 pF.

Differential:

>10

Ω

, < 200 pF.

Common Mode:

>10

Ω

, < 400 pF.

CROSS TALK (1MHz, 50

Ω

Load):

< -40 dB.

INSERTION LOSS (50

Ω

Source, 50 Load):

< 0.1dB below 1MHz, < 3 dB

below 2MHz.

RELAY DRIVE CURRENT (per relay):

16mA.

ENVIRONMENT:

Operation

C to 50

C, up to 35

C < 80% RH.

Storage:

-25

C to 65

Specifications subject to change without notice.

7012 SPECIFICATIONS

7012 4x10 Matrix

1 0

Backplane

Matrix Crosspoint

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Summary of Contents for 7012-C






























































































Search results

Summary of Contents for 7012-C

Reviews:

Keithley 7012-C, Instruction Manual, Page: 9 / 93

Search results

Summary of Contents for 7012-C

Reviews: