manualshive.com logo in svg

Keithley 7012-C, Instruction Manual, Page: 76 / 93

Share
Download
Keithley 7012-C Instruction Manual Download Page 76

 

Service Information

 

5-14

 

5.5.4 Relay power control

 

A relay power control circuit, made up of U106, U107,
Q100, Q101, and associated components, keeps power
dissipated in relay coils at a minimum, thus reducing
possible problems caused by thermal EMFs.

During steady-state operation, the relay supply volt-
age, +V, is regulated to +3.5V to minimize coil power
dissipation. When a relay is 

Þ

rst closed, the STROBE

pulse applied to U106 changes the parameters of the re-
lay supply voltage regulator, Q100, allowing the relay
supply voltage, +V, to rise to +5.7V for about 100msec.
This brief voltage rise ensures that relays close as
quickly as possible. After the 100msec period has
elapsed, the relay supply voltage (+V) drops back
down to its nominal steady-state value of +3.5V. 

 

5.5.5 Power-on safeguard

 

NOTE

 

The power-on safeguard circuit dis-
cussed below is actually located on the
digital board in the Model 7001 main-
frame.

Figure 5-10
Transmit and acknowledge sequence

ID CLK

Acknowledge

Start

1

8

9

(Data output
from mainframe
or ROM)

IDDATA

(Data output
from mainframe
or ROM)

IDDATA

 

A power-on safeguard circuit, made up of U114 (a D-
type 

ß

ip-

ß

op) and associated components, ensures

that relays do not randomly energize on power-up and
power-down. This circuit disables all relays (all relays
are open) during power-up and power-down periods. 

The PRESET line on the D-type 

ß

ip-

ß

op is controlled

by the 68302 microprocessor, while the CLK line of the
D-type 

ß

ip-

ß

op is controlled by a VIA port line on the

68302 processor. The Q output of the 

ß

ip-

ß

op drives

each switch card relay driver IC enable pin (U100-
U104, pin 8).

When the 68302 microprocessor is in the reset mode,
the 

ß

ip-

ß

op PRESET line is held low, and Q out imme-

diately goes high, disabling all relays (relay driver IC
enable pins are high, disabling the relays.) After the re-
set condition elapses (

 

≈

 

200msec), PRESET goes high

while Q out stays high. When the 

Þ

rst valid STROBE

pulse occurs, a low logic level is clocked into the D-
type 

ß

ip-

ß

op, setting Q out low and enabling all relay

drivers simultaneously. Note that Q out stays low, (en-
abling relay drivers) until the 68302 processor goes into
a reset condition.

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Summary of Contents for 7012-C






























































































Reviews:

No comments