background image

M3i INDOOR GROUP CYCLE

11

Prepare for Flywheel Guard Installation.

(a) Install the Clamps to the Flywheel Guard, finger-tight 
(Items D, E, and F).

(b) Place the open end of the Flywheel Guard onto the 

Mount Stud, then pivot the Flywheel Guard into position.

Prepare for Flywheel installation.

It is recommended to remove x2 
Flywheel Guard Mount Screws 
and Washers from the Base for 
easy installation later in the 
assembly procedure (Tool: 5 mm 

Hex Key).

Align and secure the Flywheel Guard.

(a) Attach the Clamps to the Base using x2 Mount Screws 
and Washers (removed in Step 5), finger-tight. Align the 

Flywheel Guard to the Flywheel. 

(b) Once the Flywheel Guard is aligned, tighten x2 Mount 

Screws using a 5 mm Hex Key. Complete installation by 

tightening the Bolt and Nut (Items D and E) using two 

10 mm Wrenches.

5

7

(a)  Pivot  the  Flywheel 

into the folded paper 
and onto the Hub. Push 
the Flywheel against 
the Hub until it is fully 
seated. Align the screw 
holes, and discard the 
folded paper.

(b)  Place  the  Hub  Cap 

onto the Hub. Align the 

screw holes. Start five 
SHC Screws (Item C). 

(c) Tighten the screws 

in a star pattern until 
snug using a 5 mm Hex 
Key.

DO NOT OVERTIGHTEN 

MAY DAMAGE THREADS.

6

8

IMPORTANT: Failure to follow these instructions can 

lead to cosmetic damage to the Flywheel.

Move Shifter to the down position. Wedge a 
piece of paper between the Magnets.

Hub Cap

C

(align screw holes)

Magnets

Paper

Shifter

D

E

D

E

F

HOW TO ASSEMBLE THE M3i BIKE

Bikes sold in the European Union: Apply Hub Cover Decals over each 

of the screw holes (Item L, not shown).

Hub

Flywheel

Paper

Flywheel Guard

Mount Stud

Summary of Contents for M SERIES

























Reviews: