background image

USER MANUAL 

– routine 

Slim Jim User manual 

 

page 20 

Daily to weekly routine 

Use hot water from the machine 

Even the best treated water will lead to scale deposition in the steam boiler if the steam boiler is 
predominantly used to steam milk. If the hot water-tap on the espresso machine is hardly ever used 
get into the habit of doing your daily clean-up up with mix-water drawn from the espresso-machine 
instead of from the buildings hot-water supply. 

 

Clean body 

Resistant smudges on high gloss metal panels may be removed with silver polish and a soft cloth 
(these surfaces scratch easily, even copper polish may leave marks). Other materials can be cleaned 
with window cleaner in a hand spray flask in combination with a soft, clean, cotton cloth. When the 
material is warm you have to work swiftly to prevent stripes: spray and immediately rub. 

Lift the drip tray grill from the machine and clean it with washing up liquid and a sponge. 

Activate the groups (without filter holder locked in) or let the hot water run for a moment and use a 
brush to push remains into the drain. 

 

Remove filter basket 

Materials needed 

 

Group screen extractor (or back end of teaspoon) 

Procedure 

1.  Remove the filter holder from the group and pry the filter basket out (see Figure 15)
2.  When remounting the filter basket, make sure the spring remains in the indentation of the filter 

holder and grabs the basket. 

 

Figure 15. Pry filter basket from filter holder with the group screen extractor. 

 

Clean filter holder 

Remove the filter basket from the filter holder and clean the filter basket with a little washing up liquid 
and plastic scouring pad or firm brush. Soak the metal part of the filter holder for 10 minutes in a 
solution of 1 tablespoon of coffee dissolving powder in 0.5 litre hot water. The plastic handle will 
eventually disintegrate in this solution and should thus be kept out of the solution. 

 Caution! 

Never clean the filter holder in a dish washer as dish washer detergent will ruin it. 

replace with new photo 1860 x 750 

Summary of Contents for Mirage Slim Jim

































Reviews: