background image

 2

EN

KSL-Z by KEELER

Consult instructions for use

General warning sign

Date of manufacture

Warning: Electricity

Manufacturer’s name and 

address

Warning: Floor level obstacle

Country of manufacture

Warning: Non-ionizing 

radiation

Waste Electrical and Electronic 

Equipment (WEEE) recycling

Warning: Optical radiation

This way up

Warning: Hot surface

Keep dry

Conformité Européene

Fragile

Type B applied part

Do not use if package is 

damaged

Class II equipment

Temperature limit

Atmospheric pressure 

limitation

Authorised representative in 

the European Community

Humidity limitation

Use-by date

Serial number

Catalogue number

Medical device

Translation

The Keeler Slit Lamp is designed and built in conformity with Directive 93/42/EEC, Regulation (EU) 2017/745 and 

ISO 13485 Medical Devices Quality Management Systems.
Classifi cation:  CE:  Class I
 

FDA: Class II

The information contained within this manual must not be reproduced in whole or part without the manufacturer’s 

prior written approval. As part of our policy for continued product development we the manufacturer reserve the right 

to make changes to specifi cations and other information contained in this document without prior notice.
This IFU is also available on the Keeler UK and Keeler USA websites.
Copyright © Keeler Limited 2021. Published in the UK 2021.

Summary of Contents for Z Series



























Reviews: