background image

 15

EN

KSL-Z by KEELER

7.  ROUTINE MAINTENANCE

The maintenance outlined below should only be carried out once the 

main power cable has been disconnected. If you have any problems that 

are not covered by the procedures described below, contact Keeler Ltd or 

your local supplier.

7.1  LED SYSTEMS

1.  LED’s typically have a life exceeding 10,000 hours of continuous use and therefore can 

be considered as a non-consumable item that will not require changing by a user.

2.  Whilst this is a significant life expectancy, we suggest that the Slit Lamp is always 

switched off between examinations to conserve energy and LED life.

3.  In the unlikely event of an LED failure please contact Keeler or your local distributor for 

guidance on the replacement procedure.

7.2  REGULARLY INSPECT THE DEVICE FOR DAMAGE OR DIRT

1.  Routinely clean as per section 3 on page 5 cleaning instructions.

7.3  CLEANING THE ILLUMINATION PRISM

1.  The prism should be cleaned with a soft, clean lens cloth.
2.  Care must be taken to keep the objective and the eyepiece lenses clean – use only soft, 

clean lens cloths to clean optical surfaces.

7.4  ELECTRICAL CONNECTIONS

1.  Routinely check all electrical connections, cables and connectors. 

7.5  OPTICS

1.  The optics should be wiped clean of any loose dirt or debris with a suitable dust brush 

then cleaned with a soft dry lens cloth, washed linen or other non abrasive lens cleaning 

material.

7.6  AXLE AND MECHANICAL PARTS

If the Slit Lamp becomes hard to move on the glide plate, the plate should be cleaned with a 

lightly oiled cloth or silicon polish. The axle should be cleaned only with dry lint free cloths.

8.  WARRANTY

The Keeler Z-Series Slit Lamps are guaranteed for three years against faulty workmanship 

materials or factory assembly. Warranty is on a Return To Base (RTB) basis at the cost of the 

customer and may be void if the Slit Lamp has not been regularly serviced.
The manufacturer’s warranty and terms and conditions are detailed on the Keeler UK website.
The mirror, main illumination lamp and general ‘wear and tear’ are excluded from our standard 

warranty.

Summary of Contents for Z Series



























Reviews: