Kee SGNA018GV Operation & Maintenance Manual Download

Page: 14 / 16

Single Gate Components

European Gate - Galvanized -

SGEU500GV

Spring Loaded, self-closing safety gate. Manufactured from steel to EN 10255. 33.7mm diameter tube

x 3.2mm wall thickness to meet requirements of EN 13374 & EN 14122. Complete with fixing

pack.

Material : Galvanized steel to BS EN ISO 1461. Net weight : 11kg (24lb 4oz).

466mm

500mm

466mm

500mm

European Gate – Powder Coated -

SGEU500PC

Spring Loaded, self-closing safety gate. Manufactured from steel to EN 10255 33.7mm

diameter tube x 3.2mm wall thickness to meet requirements of EN 13374 & EN 14122.

Complete with fixing pack. Powder Coated Finish to EN 13438.

Material : Steel to EN 10255. Net weight : 11kg (24lb 4oz).

SAFETY GATE NORTH AMERICAN FIXING PACK 1 -

SGNAFXPK1

Supplied for the USA market to fit posts 1.0”, 1.25” and 1.5” diameter. Fixing pack contains 3No

U Bolts for each size complete with 0.3125” and 0.375” nuts and washers.

Material : Galvanized steel to ASTM A53. Net weight : 1.44kg (3lb 3oz).

Summary of Contents for SGNA018GV

















Search results

Summary of Contents for SGNA018GV

Reviews:

Related manuals for SGNA018GV

Brands by name

Popular brands

Kee SGNA018GV, Operation & Maintenance Manual

Search results

Summary of Contents for SGNA018GV

Reviews:

Related manuals for SGNA018GV

Brands by name

Popular brands