manualshive.com logo in svg

Keba KeTop Safe Wireless System, Quick Start Manual

Share
Download
Keba KeTop Safe Wireless System Quick Start Manual Download Page 25

 

24

 

 

Illustration: Dialog for entering the password 

 
After entering the password, the base station with which the connection is to be established must be 
selected. The selection contains the names of all base stations with which a connection has already 
been established. 
 

 

Illustration: Dialog for selecting the base station 

 
After selecting the base station, a connection is temporarily established and on the base station the 
bar starts to light up in a color combination of two colors. This color combination must be confirmed on 
the handheld terminal - this mechanism guarantees a line-of-sight connection. 
 

 

Illustration: Dialog for confirming the color combination of the base station 

 
Then the connection is established and indicated by a dialog, the bar of the base station turns green 
and the emergency stop is illuminated. 
 

 

Illustration: Dialog confirming that the connection exists 

 

Summary of Contents for KeTop Safe Wireless System





























Reviews:

No comments

Brands by name

Popular brands

Load more brands