Keba KeTop Safe Wireless System Quick Start Manual Download | Manualshive

Page: 11 / 28

background image

10

Illustration: Successful closing of the connection between base station and handheld terminal

5. Configuration

To configure the base station and/or the handheld terminal, these two must first be connected (see
chapter 4). For the configuration, the DeviceConfig tool is available on the handheld terminal, with
which both the base station and the handheld terminal can be configured.

Illustration: Windows Desktop with DeviceConfig tool

After starting the DeviceConfig tool, different menus can be selected.

Illustration: Main menu DeviceConfig tool

«
...
9
10
11
12
13
...
»

Summary of Contents for KeTop Safe Wireless System





























Reviews:

No comments

Related manuals for KeTop Safe Wireless System

Brand: ABB Pages: 52

Brand: Lawler Pages: 4

Brand: Zeagle Pages: 37

Brand: Gascat Pages: 32

Brand: Garz & Fricke Pages: 35

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: RADVision Pages: 39

Brand: QNAP Pages: 35

Brand: Rabe Pages: 61

Brand: Racal Instruments Pages: 35

Brand: Rane Pages: 2

Brand: Safeline Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands