background image

1

I INTRODUCTION

GENERAL

Keating MIRACLEAN

®

or polished steel Teppanyaki

Griddles are designed to give maximum production
efficiency, delivering high quality food products. The
following design features are incorporated into Keating
MIRACLEAN

®

or polished steel Teppanyaki Griddles.

STANDARD
FEATURES

MIRACLEAN

®

or polished steel energy efficient plate

Baffled grease drawer with rear handle

Stainless steel control panel

OPTIONS

Welded stainless steel perimeter

Front drain trough

STANDARD ACCESSORIES FOR
MIRACLEAN

®

TEPPANYAKI

GRIDDLE

Keating griddle scraper

Package of 10 scraper blades

Keating Klenzer sample

Palmetto Brush

STANDARD
ACCESSORIES FOR
POLISHED STEEL
TEPPANYAKI
GRIDDLE

Keating Klenzer sample

ELECTRICAL

All 230V = 1 Phase

MODEL VARIATIONS

Keating Teppanyaki Griddles can range in size from
24'' (610mm) x 24'' (610mm) to 72'' (1829mm) x 30''
(762mm). The actual heating surface on all sizes is
24''W (610mm) x 18''D (457mm).

SAFETY
PRECAUTIONS

THIS SYMBOL WARNS YOU THAT SERIOUS BURNS
OR OTHER INJURIES MAY RESULT IF SAFETY
INSTRUCTIONS ARE NOT FOLLOWED.

THIS APPLIANCE MUST BE EARTHED.

This service manual should be retained in a safe
place for future reference.

The installation of your new griddle must conform to
local codes.

Your ventilation hood, when installed, must conform
to the current standard.

Installation clearance requires 6" (152mm) from rear
and side walls and supporting surfaces regardless of
size of unit. 6"/152.4mm side clearance also
required below the cooking surface.

Adequate clearance for servicing and proper
operation must be maintained. Your Keating
MIRACLEAN® is designed to be serviced from the
front, except for the rear field wire connections
(electric input).

Keating commercial griddles are intended for other
than household use.

ALWAYS instruct new employees on proper griddle
operation.

A MIRACLEAN

®

griddle should be operated ONLY

by properly trained personnel.

ALWAYS turn griddle off each night.

ALWAYS disconnect electrical supply before
servicing.

NEVER leave a griddle unattended during operation.

NEVER move griddle when hot.

NEVER submerge in water.

THIS GRIDDLE MAY NOT BE ALTERED, MODIFIED
OR CHANGED IN ANY WAY.

Safe operation of this equipment is
possible only when the operating
instructions and the safety
precautions are read completely
and the instructions are strictly
observed. Before operating this
equipment, ask for a practical
demonstration.

WARNIN

G

WARNIN

G

CAUTION

Read all operating and 

safety instructions

before using equipment.

Summary of Contents for Teppanyaki Griddle












Reviews: