background image

1

INTRODUCTION

GENERAL

Keating MIRACLEAN

®

Electric Griddles are designed

to give maximum production efficiency, delivering high
quality food products. The following design features are
incorporated into Keating MIRACLEAN

®

Electric

Griddles.

STANDARD
FEATURES

MIRACLEAN

®

energy efficient plate

Welded stainless steel perimeter

Welded stainless steel grease trough

Baffle grease drawer with rear handle

Stainless steel control panel

STANDARD
ACCESSORIES

Keating griddle scraper

Package of 10 scraper blades

Palmetto brush

4” special Keating spatula

Keating egg turner

Keating Klenzer sample

OPTIONS

380 or 480 volt input

Single phase input

High input heating elements

MODEL VARIATION

Standard Griddles: Keating MIRACLEAN

®

electric

griddles are available in widths ranging from 24” to
72” and in 24”, 30” and 36” depths. The electric
griddles are ETL listed.

SAFETY PRECAUTIONS

THIS SYMBOL WARNS YOU THAT SERIOUS BURNS
OR OTHER INJURIES MAY RESULT IF SAFETY
INSTRUCTIONS ARE NOT FOLLOWED.

This service manual should be retained in a safe
place for future reference.

The installation of your new griddle must conform to
local codes or in the absence of local codes, with the
current National Electrical Code ANSI/NFPA 70 or
Canadian Electrical Code CAN 22.2 as applicable.

Your ventilation hood, when installed, must conform
to the current ANSI/NFPA 96 standard.

Installation clearance requires 6” from rear and side
walls.

You must maintain this appliance free and clear from
combustibles.

Adequate clearance for servicing and proper
operation must be maintained.

Your Keating MIRACLEAN

®

is designed to be

serviced form the front, except for the rear field wire
connections (electric input).

Keating commercial griddles are intended for other
than household use.

ALWAYS instruct new employees on proper griddle
operation.

A MIRACLEAN

®

griddle should be operated ONLY

by properly trained personnel.

ALWAYS turn griddle off each night.

ALWAYS disconnect electrical supply before
servicing.

NEVER leave a griddle unattended during operation.

NEVER move griddle when hot.

THIS GRIDDLE MAY NOT BE
ALTERED, MODIFIED OR
CHANGED IN ANYWAY.

Safe operation of this equipment is
possible only when the operating
instructions and the safety
precautions are read completely
and the instructions contained
therein are strictly observed. Before
operating this equipment, ask for a
practical demonstration.

Periodically inspect cable and plug,
if provided, before using machine.
Servicing should be performed by
qualified and licensed service
companies.

CAUTION

Read all operating and 

safety instructions

before using equipment.

WARNIN

G

Plug into a 

properly grounded

three-prong receptacle.

Summary of Contents for Griddle






















Reviews: