manualshive.com logo in svg

KBL megaSun 6700 a business, Assembly Instructions Manual

Introducing the KBL megaSun 6700 - a business essential for an impeccable tanning experience. Our Assembly Instructions Manual ensures easy setup, guiding you step-by-step. Download the free manual today from manualshive.com to unlock the full potential of your megaSun 6700, and bask in the sun-kissed glow it offers.

Share
Download
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

42

6.6 aquaCool and Aroma
       connections

AQUACOOL

The  aquaCool  box  is  equipped  with  a  liquid-

level  sensor 

①

  as  well  as  with  a  connection  to 

the  aquaCool  canister 

②

.  Furthermore,  the  box 

houses  the  compressor  ensuring  the  compressed-

air supply 

③

, and the Aroma box 

④

 with its related 

connections.

①

②

④

③

1

Connector (liquid-level monitoring)

2

Connection to aquaCool canister

3

Compressor with compressed-air 

connection

4

Aroma box

AROMA

The Aroma box is attached within the aquaCool box 

and equipped with three hose connections, one for 

the compressed-air supply 

⑤ 

and two leading to the 

Aroma nozzles 

⑥

.

⑥

⑥

⑤

5

Aroma box (inlet)

6

Aroma box (outlets)

6.7 Initial operation

• Insert batteries in colorMotion remote control unit.

• Turn on the supply voltage.

• Start the aquaCool initialisation before tanning for 

the fi rst time. Service menu “Aqua / aquaCool Start 

Initialisation“ 

• Test all functions in a trial run.

• Remove all protective fi lms.

• Clean the tanning device.

Summary of Contents for megaSun 6700 a business













































Reviews:

No comments

Related manuals for megaSun 6700 a business

Brands by name

Popular brands

Load more brands