manualshive.com logo in svg

KBL megaSun 6700 a business, Assembly Instructions Manual

Introducing the KBL megaSun 6700 - a business essential for an impeccable tanning experience. Our Assembly Instructions Manual ensures easy setup, guiding you step-by-step. Download the free manual today from manualshive.com to unlock the full potential of your megaSun 6700, and bask in the sun-kissed glow it offers.

Share
Download
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

23

4.8.2 REMOVE FRONT PLASTIC CLADDING

• Disconnect the two plug connectors D1/D2 in the 

control panel tray.

•  Loosen three M6x16 countersunk screws each on 

both

 sides left/right. 

6

•  Lower  the  canopy  (second  person)  and  loosen 

the  two  rear  knurled  nuts.  Only  on 

7908

  tanning 

devices.

• Open the canopy and evenly press the front edge 

of the cladding on both sides a little bit upwards.

• Then gently pull the rear edge of the cladding from 

the slot.

In  7908  devices,

  also  lift  the  cladding 

from the bolts of the knurled nuts.

•  Lift the cladding out towards the front.

• Transport it to the installation site and set it down 

safely on protective padding.  

Summary of Contents for megaSun 6700 a business













































Reviews:

No comments

Related manuals for megaSun 6700 a business

VDL Hapro TOPAZ 10/1V Manual preview
Hapro TOPAZ 10/1V
Brand: VDL Pages: 16

Brands by name

Popular brands

Load more brands