Invoke the
PIN II
menu.
Press 5 (plus button) or 0 (minus button) to select
easyCare
.
Open the submenu by pressing START and then
select
EC.TIME
using 5 (plus button) or 0 (minus
button).
Enter a duration of time between 8 and 20 minutes.
Press START to save the settings and STOP to
exit the menu.
DISPLAy ERyThEMA-EFFECTIVE IRRADIANCE
This value is given for information only.
Invoke the
PIN II
menu.
Press 5 (plus button) or 0 (minus button) to select
easyCare
.
Press START to open the submenu and select
Ee-
rLi
(bed) or
EerDe
(canopy) using 5 (plus button)
or 0 (minus button).
Exit the menu by pressing STOP.
TANNING CONTROL ONLy VIA EASyCARE
you can determine whether easyCare can be
deactivated or not.
Invoke the
PIN II
menu.
Select
easyCare
by pressing 5 (plus button) or
0 (minus button).
Press the START button to open the submenu and
select
EConly
using 5 (plus button) or 0 (minus
button).
Select the desired setting by pressing 4 (plus
button) or 9 (minus button). ON=easyCare
cannot be deactivated, OFF=easyCare can be
deactivated.
Press START to save the settings and leave the
menu by pressing STOP.
SESSION TIME AT EASyCARE UNIT POSSIBLE
here you can determine whether it will be possible to
set the session time via the easyCare display.
Invoke the
PIN II
menu.
Select
easyCare
by pressing 5 (plus button) or
1.
2.
3.
4.
5.
1.
2.
3.
4.
1.
2.
3.
4.
5.
1.
2.
0 (minus button).
Press START to open the submenu and select
T.Display
by pressing 5 (plus button) or 0 (minus
button).
Select the desired setting by pressing 4 (plus
button) or 9 (minus button). ON=setting via display
possible, OFF=setting via display impossible.
Save the settings by pressing START and exit the
menu via STOP.
SENSOR TEST
The sensor test is carried out to check whether the
sensor is functional.
Invoke the
PIN II
menu.
Select
easyCare
by pressing 5 (plus button) or
0 (minus button).
Press START to go to the submenu and select
TEST
by pressing 5 (plus button) or 0 (minus
button).
Press the sensor onto the skin in order to start
the test.
Press STOP to leave the menu.
RELAy TEST
The relay test is used to test the functionality of any
possible combination of power levels of tubes and
sunlamps. In order to be able to carry out this test,
there must be an incoming timer signal.
Invoke the
PIN II
menu.
Select
easyCare
by pressing 5 (plus button) or
0 (minus button).
Open the submenu by pressing START and select
EC-REL. TEST
using 5 (plus button) or 0 (minus
button).
Press 1 (minus button) to start the test.
Press the STOP button to exit the menu.
Entering PIN III
④
If you enter your PIN Ill here, you will access the next
service level. Level III is exclusively reserved for trained
service staff!
3.
4.
5.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
M a n u a l e o p e r a t i v o
|
megaSun 5800
Summary of Contents for megaSun 5800
