Kaysun KMF-400 DN3 Installation Manual Download Page 19 | Manualshive

Page: 19 / 20

background image

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a

similarly qualified person in order to avoid a hazard.

An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be

connected in fixed wiring.

The appliance shall be installed in accordance with national wiring regulations.

The temperature of refrigerant circuit will be high, please keep the interconnection cable away from

the copper tube.

The power cord type designation is H05RN-R or above/H07RN-F.

MD13I-052CW(DZD)

16127000A03538

«
...
17
18
19
20
»

Summary of Contents for KMF-400 DN3





















Reviews:

No comments

Related manuals for KMF-400 DN3

Brand: Kampmann Pages: 28

Brand: Kampmann Pages: 3

Brand: Kampmann Pages: 72

Brand: Zokop Pages: 21

Brand: Friedrich Pages: 28

Brand: Nordyne Pages: 36

Brand: Nibe Pages: 80

Brand: Kärcher Pages: 48

Brand: AIROCIDE Pages: 24

Brand: nedis Pages: 16

Brand: Innova Pages: 24

Brand: Daikin Pages: 76

Brand: Danby Pages: 56

Brand: Hamilton Beach Pages: 28

Brand: Koldfront Pages: 23

Brand: GE Pages: 70

Brand: GE Pages: 60

Brand: Daikin Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands