KAYO MOTOR TT 125 Service Manual Download Page 13 | Manualshive

Page: 13 / 74

background image

Front brake caliper

Throttle

Throttle

The throttle is located on the right side of the handlebar and is
controlled by right hand rotation. Turn the throttle up when
turning the handle counterclockwise, then turn the handle back
to the position after releasing the handle.

Ignition

Starting lever

The vehicle starting lever is located on the right side of the
engine, and the motorcycle engine can be started by stepping on
the starting lever.

Note:

The brake should be pinched when starting to prevent the

engine from starting with the gear.

Note:

there should be fuel in the fuel tank before starting the

engine, and the fuel tank switch should be in the open position.

Stall

Stall switch

The stall switch of the engine is located on the left side of the
handlebar near the handle cover. It is a round red button. Long
press it to turn off the engine and make it stall.

Fuel tank switch

The fuel tank switch is located on the bottom left side of the
tank. By rotating the switch, you can control the fuel to flow

«
...
11
12
13
14
15
...
»

Summary of Contents for TT 125











































































Reviews:

No comments

Related manuals for TT 125

Brand: Memphis Shades Pages: 2

Brand: Memphis Shades Pages: 2

TorqDrive Clutch Pack

Brand: Rekluse Pages: 18

Brand: Honda Pages: 98

Brand: yasuni Pages: 9

Brand: hepco & becker Pages: 4

Brand: DYNATEK Pages: 12

Brand: Royal Enfield Pages: 110

Brand: BMW Pages: 205

2004 Moto Matrix

Brand: Yamaha Pages: 41

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 28

2004 FJR1300(S)

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 87

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands