8/07
x
First insert the hinge pin in the top hole in the collar and then put the washers on top of it (the
notches in the pine must be at the lower end).
x
Hang the door on the hinge pin above the collar.
x
Finally, guide the hinge pin into the bottom holes of the collar and fire door.
The swing of the all-metal fire door is changed in the same way.
2.8.2 GLASS FIRE DOOR
Handle the glass fire door with care
. Do not slam the door nor use it to push logs into the fire box. ¨
K-007, KL-16VE
To change a broken glass, do as follows:
x
Remove the fire door as explained in section 2.8.1.
x
Open the fastenings and remove any glass splinters and the old seal.
x
Put the new glass and seals in place.
x
Then insert the lugs onto the threaded pins and the sealing pads between the glass and the hard tip.
x
Insert the washers and nuts.
x
Tighten the nuts. Check that the glass, seals and lugs are firmly in position.
Do not tighten the nuts too much.
x
Replace the fire door according to the instructions given in section 2.8.1.
2.9. HOT WATER TANK
2.9.1 WATER TANK LID
Remove the water tank lid (remove the protective plastic cover) and fix the knob to the outside of the
lid with a screw.
2.9.2 WATER TANK TAP
To avoid damage in transportation, the tap is fixed to the inside of the water tank. The kit includes a
tap, two seals and a nut. The tap is installed as follows: (Fig. 1)
x
Lift off the water tank.
x
Insert seal 1 onto the threaded section of the tap.
x
Insert the tap into the hole in the heater mantle.
x
Insert seal 2 onto the threaded section of the tap inside the mantle.
x
Lift the water tank in position and fit its hole into the threaded section of the tap.
x
Place the edge of the water tank on top of the side bracket.
x
Insert the nut onto the threaded section of the tap and tighten it with a suitable tool from inside the
tank.
2.9.3 KL-16VE: INSTALLATION OF THE HOT WATER TANK
Remove the water tank lid and fix the knob to the outside of the lid with a screw.
The water tank tap can be installed on either side of the heater. Do as follows:
x
Lift the water tank off.
x
Remove the plate covering the tap hole on the side where you want to install the tap.
x
Fasten the water tank adjusting pin to the heater front frame as follows (Fig. 4).
x
Insert the adjusting pin screw into the hole from under the frame so that the hook of the adjusting pin
on the side facing the tank points upwards.
x
Insert the washer and nut onto the screw and tighten it so that adjusting pin moves with some
resistance. It must not be too loose. Then screw the knob in position.
x
Lift the hot water tank in position while making sure that it is the right way round. The lower end of
the tank must rest on the bracket and the hook of the adjusting pin must fit under the bend in the
front edge of the water tank. Test the adjusting pin to see that the adjusting pin and tank move.
x
Fasten the tap according to the instructions given in section 2.9.2.
3. USING THE HEATER
4211-60
Kastor K-007, KL16VE
5
3/25/11
Rev. 1
Summary of Contents for K-007
