Kasco J Series, Owner'S Manual, Page: 8 / 14

8
Model Height Width
3400JF/HJF 7’ 17’
4400JF/HJF 9’ 28’
Birch Display :
The Birch nozzle (marked B on the part)
DWG. NO.
3400J SERVICE
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
X
3400J SERVICE PRINT
X
NONE
X
AS NOTED ABOVE
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
3400J SERVICE
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:20
Model Height Width
3400JF/HJF 7’ 5’
4400JF/HJF 11’ 8’
Willow Display
:
No nozzle installed
Model Height Width
3400JF/HJF 6.5’ 21’
4400JF/HJF 9’ 31’
Installation Instructions
Use the ropes to position the Fountain in the desired
location in the pond/lake. Anchor the ropes or secure
them to the shoreline so the ropes are free of slack, but
not tight. To prevent twisting of the unit due to torque,
you should place the anchor at least 3 feet from the
float for each foot of depth (Ex. A 6 foot deep pond
would require an anchor 18 feet horizontally from the
float.)
Nozzle Options
NOTE: Pattern sizes listed are approximate. Varia-
tions in voltage caused by regional electrical differenc -
es or voltage drop due to long power cords may result
in reduced pattern sizes.
To install, place oring around outlet and simply twist
the nozzle into the 3 locking tabs.
Sequoia Display
:
The Sequoia nozzle (marked S on the part)
DWG. NO.
3400J SERVICE
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
X
3400J SERVICE PRINT
X
NONE
X
AS NOTED ABOVE
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
3400J SERVICE
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:20
DWG. NO.
431230
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
3400J 4400J
NOZZLE, SEQUOIA
FREE OF FLASH
CLEAN
BLACK
VALOX 357
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
431230
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:2
Model Height Width
3400JF/HJF 13’ 8’
4400JF/HJF 18’ 11’
Linden Display :
The Linden nozzle (2 piece assembly with bolt)
DWG. NO.
3400J SERVICE
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
X
3400J SERVICE PRINT
X
NONE
X
AS NOTED ABOVE
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
3400J SERVICE
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:20
Model Height Width
3400JF/HJF 9’ 29’
4400JF/HJF 12’ 31’
Cypress Display :
The Cypress nozzle (marked C on part)
DWG. NO.
3400J SERVICE
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
X
3400J SERVICE PRINT
X
NONE
X
AS NOTED ABOVE
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
3400J SERVICE
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:20