Kärcher VC 6 Cordless ourFamily, Instructions Manual

Page: 9 / 16

English 9
Mounting the wall bracket/
freestanding parking station with
charging function
Depending on the scope of delivery, a wall bracket or a
free-standing parking station with charging function is
included for correct storage of the vacuum cleaner and
accessories.
● Install wall bracket
Note
Mount the wall bracket at a suitable point using the
screws and dowels supplied.
For safe storage of the device, the lower screw fasten-
ing of the wall bracket should be placed at a distance of
0.83-0.85 m from the floor.
Illustration F
ATTENTION
Material damage due to incorrect installation
Incorrect installation can damage both the device and
the floor covering if it falls.
Use suitable mounting tools for wall mounting.
Take the weight of the device and the loading capacity
of the installation location into account when selecting
the fasteners.
몇
WARNING
Risk of electric shock and injuries
Make sure there are no electrical cables, water or gas
pipes in the wall around the mounting area.
● Install free-standing parking station
Note
Mounting on the wall is not necessary.
1 Plug the base, connecting tube and holder together
and let them click into place.
2 Place the device in the holder.
Illustration G
ATTENTION
Risk of injury or
material
damage
If the parking station is placed in an unfavorable position
(e.g. in the middle of a room), you can trip over it and in-
jure yourself and/or the device can be damaged by fall-
ing over.
Place the device with the parking station in a safe, quiet
place (e.g. wall, corner).
Note
Dismantling is done by pressing the release buttons on
the back of the parking station on the stand and bracket.
Initial startup
Installing accessories
Note
The multi-function brush is also driven by its own inte-
grated motor and must therefore always be connected
directly to the hand-held device or the suction pipe in or-
der to ensure the power supply.
All other accessor parts can also be used directly with
the hand-held device or with the suction pipe to increase
the reach.
 Push the suction pipe on to the suction fitting of the
dust container until it audibly clicks into place.
 Press the unlocking button and remove the suction
pipe from the suction fitting.
Illustration B
 Push the floor nozzle on to the suction pipe until it
audibly clicks into place.
 Press the unlocking button and remove the floor
nozzle from the suction pipe.
Illustration C
 Push accessory, such as the crevice nozzle, on to
the suction fitting of the dust container or suction
pipe until it audibly clicks into place.
Illustration D
Inserting the battery
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Note
Use only fully charged batteries.
1. Push the battery into the mounting in the device until
it audibly latches into place.
Illustration E
Battery charging
Note
The device is not supplied with a charged battery. Fully
charge the battery before using it for the first time.
Please observe the enclosed safety instructions for bat-
tery powered vacuum cleaners.
Note
The battery can be charged with the device or separate-
ly (e.g. for variants with an additional battery).
Note
For a detailed description of the LED displays, see
chapter LED display
1. Charge the battery with the device.

To charge the device, attach it to the wall bracket
with charging function included in the scope of
delivery.
Illustration F
2. Charge the battery separately.
 Place the battery on a flat and safe surface to
charge it.
ATTENTION
Material damage due to incorrect battery storage
Incorrect storage during charging can result in the bat-
tery e.g. falling down or damaging heat-sensitive surfac-
es.
Make sure charging of the separate battery takes place
on a flat, smooth and heat-insensitive surface.
Furthermore, the battery should not be covered with ob-
jects (e.g. fabrics or papers) while it is being charged.
3. Plug the charger into a socket.
Insert the connecting plug into the charging socket
of the wall bracket / battery.
Depending on the battery status, the 3 LED indicator
lights flash or light up green during the charging pro-
cess.
Illustration H
4. When the device is fully charged, all 3 LED indicator
lights light up continuously green for 2 minutes and
then go out.
Remove the charger from the socket/charging cable
from the battery charging socket and socket.
Illustration I
5. Remove the device from the wall bracket or insert
the battery into the device, see chapter Inserting the
battery
The device is ready for use.