Kärcher VC 6 Cordless ourFamily, Instructions Manual

Page: 11 / 16

English 11
5. Clean the air inlet filter, see chapter Cleaning the air
inlet filter
6.
7.
Depending on the scope of delivery, attach the de-
vice to the wall bracket or to the free-standing park-
ing station with charging function.
Illustration F
/ Illustration G
Depending on the scope of delivery, attach the de-
vice to the wall bracket.
Illustration A
D / Illustration AE
8. Charge the device with a battery or only a battery,
see chapter Battery charging.
How to use the Accessories
General instructions for use
 Which accessories are included in the scope of de-
livery is shown on the device packaging.
 Accessories not included in the packaging can be
purchased in a KÄRCHER specialist shop or from
www.kaercher.com.
 Test the accessory at an inconspicuous point before
using it in a sensitive area.
 Follow the manufacturer's cleaning instructions.
 Connect the motor-driven electric nozzle to the suc-
tion pipe or the hand-held device.
 Also connect the other accessory parts, such as
crevice nozzle, to the hand-held device or push it di-
rectly onto the suction pipe to increase the reach.
Motor-driven multi-function brush
Ideal for hard floors and carpets.
The motor-driven multi-function brush removes dirt
stuck between the carpet fibres particularly effectively.
2-in-1 upholstery nozzle
The frame with the surrounding bristles can be taken off
pressing the unlocking button.
● The soft brush is suitable for furniture with hard sur-
faces
● The wide brush is used to clean upholstered furni-
ture, curtains, etc.
Crevice nozzle
For edges, joints, heaters and areas that are difficult to
reach.
Soft brush
The soft brush has particularly soft bristles for cleaning
sensitive surfaces such as keyboards, lamps, etc.
Flexible crevice nozzle
The flexible crevice nozzle increases the reach. For
cleaning hard-to-reach places, such as between the car
seats.
Flexible extension hose
Due to the extension and flexibility, hard-to-reach areas
such as in the car can be reached and cleaned.
Large upholstery nozzle
For cleaning textile surfaces such as sofas, armchairs,
mattresses, car seats, etc.
2-in-1 furniture brush
For gentle cleaning of sofas and delicate furniture. De-
pending on requirements, the accessory can be used as
a furniture or upholstery nozzle by pressing the button.
Mini turbo brush
Efficiently removes pet hair and dust particles from up-
holstered furniture, mattresses or other soft surfaces.
The rotating round brush catches even the finest hair.
LED-crevice nozzle
For cleaning corners and hard-to-reach areas. The illu-
mination makes even the finest dust visible in dark
spaces.
Soft motor-driven brush (Hard floor nozzle)
For hard floors and sensitive wooden floors. Extracts
coarse and fine dirt simultaneously.
Transportation
The battery has been tested in accordance with the rel-
evant rules for international transport, and can be
transported / shipped.
Storage
ATTENTION
Moisture and heat
Risk of damage
Store battery packs indoors only, at low humidity and
temperatures below 20°C.
The battery pack display shows the current charging
state during storage.
Care and service
General care instructions
 Clean the device and plastic accessory parts with a
commonly available plastic cleaner.
Cleaning the air inlet filter
Note
The device can be cleaned manually or using a filter
cleaning device.
Cleaning the air inlet filter manually
1 Switch off the device.
2 Pull the soiled air inlet filter down at the filter stick,
carefully beat it and clean it with a damp cloth or run-
ning water.
Illustration N
a Reinsert the fully dried air inlet filter.
b Check for correct seating.
Cleaning the air inlet filter with a filter cleaning de-
vice
Note
A new air inlet filter must be installed in the dust contain-
er during filter cleaning.
1 Switch off the device.
2 Push the filter cleaning device on to the suction pipe
branch and pull the air inlet filter out of the device us-
ing the filter stick.
Illustration O
a Push the soiled air inlet filter into the filter clean-
ing device.
b Insert a new air inlet filter into the dust container.
c Switch on the device and let it run in boost mode
while turning the side cover.
Illustration P
d Remove the cleaned air inlet filter from the filter
cleaning tool and reinsert it in the dust container
after removing the new air inlet filter.
e Check that the air inlet filter is correctly seated.