background image

     

7

For float position:

Press the multi-function lever all the 
way forward and lock it in.

The rear left hydraulic connection is ac-
tivated via the lever.

You can use the drive position rotary knob 
to select the working and driving position.

Important

The driving direction selector switch must 
be set to NEUTRAL/STOP before you can 
use the drive position rotary knob!

If the drive pedal is pressed, the motor 
speed will increase. The pedal is spring-
loaded; if you remove your foot, the motor 
speed will decrease.

Important

During transport drives, use the drive pedal 
carefully, because there is a risk of sudden 
speed decrease!

The document pouch is located behind 
the driver's seat. Always keep the en-
closed documents in this pouch. This 
way, you and possible transport com-
panies will always have access to im-
portant information.

Danger

Risk of explosion!

Only use the fuels specified in the Op-
erations Manual. 

Do not refuel the machine in enclosed 
spaces.

Smoking and naked flames are strictly 
prohibited. 

Ensure that no fuel reaches the hot 
open surfaces.

Switch off engine.

Open fuel filler cap.

Fill in diesel.

Insert the fuelling gun as deep as possi-
ble into the fuel nozzle. Do not add any 
more fuel once the fuelling gun stops 
according to the settings.

Wipe off any spilt fuel and close fuel fill-
er cap.

Estimate the fuel requirement in order 
to avoid overflows.

The reservoir for windshield wiper fluid is 
located on the rear right side of the ma-
chine.

Check the fluid level daily and refill 
commercially sold windshield wiper flu-
id as necessary.

Danger

Danger of accident. Do not adjust the driv-
er's seat while driving.

1 Arm rest incline
2 Lever for seat adjustment
3 Spring hardness
4 Height adjustment
5 Damping

The left arm rest can be folded up to get 
in and out. 

The right arm rest can be adjusted for 
incline, height and position, matching 
the control of the multi-function lever.

Danger

Danger of accident. Do not adjust the steer-
ing wheel position while driving.

1 Locking

Pull on the lock.

Set the steering wheel to the desired 
position.

Slide the lock back and make sure it 
locks in.

Danger

Risk of accidents, injuries. If one point of 
the safety check is not fullfilled, the appli-
ance must not be taken into operation, but 
must be repaired.
The safety check must be performed be-
fore each use of the appliance.

Check the hydraulic oil level.

Check engine oil level.

Check cooler water level.

Control for rear work hydraulics

Drive position preselector 

WORK RANGE 1:
For hydraulic attachment. The 
max. speed represents the set mo-
tor speed.

Important

! The speed is then reg-

ulated electronically via the drive 
pedal.

WORK RANGE 2:
Working position with load sens-
ing. When the load on the attach-
ment fluctuates, the working speed 
is regulated electronically.

SLOW TRANSPORT RANGE:
The drive speed is regulated via 
the drive pedal. Max. speed ap-
prox. 20 km/h.

FAST TRANSPORT RANGE:
The drive speed is regulated via 
the accelerator pedal. Max. speed 
approx. 30 km/h or 40 km/h with 
speed level 2.

Drive pedal (foot accelerator)

Before Startup

Prior to initial start-up

Refuelling

Fuelling using a can

Windscreen washer system

Adjusting driver's seat

Set the steering wheel position

Prior to start/safety test

Controls on the right side of the machine

9

EN

Summary of Contents for MIC 45 advanced




















Reviews: