background image

 Operating instructions

KM 100/100 R B / KM 100/100 R LPG

English

40

!

  Pull out handle of filter bracket to

limit and engage it

!

  Take out finned filter

!

  Insert the new filter

!

  On the drive side, engage the

carrier into the holes

!

  Re-engage the handle of filter

dedusting

Note:

Make sure when mounting the new
filter that the lamella are not
damaged

Replacing the filter box

seal

Remove filter box seal from the
groove in the unit cover and insert
the new seal

Checking traction belt

 Danger!

The engine takes approx. 3...4 s to
run down after being shut off.
Never enter operating area during
this period!

!

  Turn ignition key to "0" and

remove it

!

  Open unit cover, engage stay bar

Check round belts and V-belts for
tightness, wear and damage

Changing fuses

The drive control electronics are
beneath the front covering.
The front covering must be removed
when a fuse needs replacing.

!

  Unscrew the screws at both sides

of the covering

Note:

 See interior for fuse allocation

 Use only fuses with the same

current rating

!

  Replacing blown fuses

!

 Refasten front covering

Fault instructions

Machine will not start

!

  Sit on the driver seat

!

  Fill up fuel or change gas cylinder

!

  Check the petrol- and gas-line

system, connections and joints

!

  Charge the battery

!

  Check and clean spark plugs,

replace if necessary

!

  Notify the Kärcher service station

Engine runs erratically

!

  Clean or replace the air cleaner

!

  Check the petrol- and gas-line

system, connections and joints

!

  Notify the Kärcher service station

Motor running but machine not
moving

!

  Check position of freewheel lever

!

  Notify the Kärcher service station

Engine runs, but machine only
moves slowly

!

  Warm up the machine for

approx. 3 min. at temperatures
below zero

!

  Notify the Kärcher service station

Machine not sweeping properly

!

  Check main brush and side brush

for wear, replace them, if
necessary

!

  Check the operation of the

coarse-dirt flap

!

  Check sealing strips for wear,

adjust or replace them as
required

!

  Check (sweeping) hydraulic

system for leaks

!

  Check the seal on the vacuum

system

!

  Notify the Kärcher service station

Summary of Contents for KM 100 R B



























Reviews: