background image

5

This wand features a 0º pencil jet which rotates 360º
for maximum dirt cutting action, effectively increasing
cleaning performance up to 50%. This wand combines
the cleaning performance of a 0º pencil jet with the
surface coverage of a wide angle nozzle.
Not recommended for soft materials, siding, painted
surfaces, decks or autos.

Dirtblaster

®

wand

Vario spray wand

The Vario spray wand allows you to adjust the cleaning pressure. To clean at maximum 
pressure, the Vario wand must be positioned to the high pressure setting (+).
To apply detergent, the wand must be positioned to the low pressure setting (-).

For lower 

pressure turn

wand collar in the

minus (-) direction.

For higher

pressure turn

wand collar in the

plus (+) direction.

WARNING 

TO AVOID SERIOUS INJURY,
NEVER POINT SPRAY NOZZLE AT
YOURSELF, OTHER PERSONS
OR ANIMALS.

USING THE ACCESSORIES

GFCI INSTRUCTIONS

Step 1

Plug the Ground

Fault Circuit Interrupter (GFCI)
into a working outlet.

Step 2

Press “TEST”, then

press “RESET” to assure proper
connection to power.

Note:
The actual
appearance
of the GFCI
may be
different from
this
illustration.

This brush is ideal for removing stub-
born dirt and stains from finished sur-
faces. Use with detergents only.

Wash brush

Summary of Contents for K360 M













Reviews: