background image

11

TROUBLESHOOTING 

– continued

Symptom Cause 

Solution

No detergent.

Garden hose 
connection leaks.

Pump is noisy.

Water leaks 
from pump.

Oil Drip.

Detergent is too thick.

Dilute detergent, for best results 
use Kärcher detergent.

Filter on detergent suction 
tube is clogged.

Run warm water through filter 
to remove debris.

Damaged or clogged 
detergent suction tube.

Remove obstruction or 
replace detergent suction tube.

Spray wand is in 
high pressure position.

Turn spray wand tip to 
low pressure position.

Discharge nozzle 
is obstructed.

Blow out or remove debris 
with fine needle.

Loose fittings.

Tighten fittings.

Missing/worn rubber washer. Insert new washer.

Spray wand extension 
not properly attached.

Broken o-ring.

Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.

Loose fittings.

Check that all fittings are tight.

Call service center.

Water seals are 
damaged or worn.

Call Kärcher customer service 
hotline and order an o-ring.

Pump is sucking air.

Oil seals are damaged 
or worn.

Call service center.

Spray wand 
or Spray wand
extension leaks.

Spray wand not 
properly attached.

Insert the spray wand of your choice into
the the wand extension. Push in and
turn clockwise to lock wand in place.

Insert the spray wand extension into
the trigger gun. Press in against the
spring tension and twist into the lock
position. Turn the spray wand exten-
sion collar clockwise until tight..

Detergent suction tube not
properly connected to the
machine.

Check connection.

If you encounter any additional 
difficulties not listed, please call 
our service center for help.

Kärcher Customer Support USA

Detergent container is empty.

Add more detergent.

In USA Call:

1-800-537-4129

or visit our website: www.karcher-usa.com

Summary of Contents for K360 M













Reviews: