background image

PARTS SUPPLIED

See your Owner’s Manual for details on how to contact us regarding installation questions

- Fire Hazard

WARNING

• Appliance installation must be performed by a qualified 

installer.

• Install the appliance according to these instructions 

and local codes.

• 

DO NOT

 install a clothes dryer with flexible plastic venting 

materials. If flexible metal (semi-rigid or foil-type) duct is 
installed, it must be UL-listed and installed in accordance 
with the instructions found in “Connecting the Dryer 
to House Vent” later in this manual. Flexible venting 
materials are known to collapse, be easily crushed and 
trap lint. These conditions will obstruct dryer airflow and 
increase the risk of fire.

• 

DO NOT

 install or store this appliance in any location 

where it could be exposed to water or weather.

• To reduce the risk of severe injury or death, follow all 

installation instructions.

• Save these instructions. (Installers: Be sure to leave 

these instructions with the customer.)

In the Commonwealth of Massachusetts, 

the following installation instructions apply: 

• Installation must be performed by a qualified or 

licensed contractor, plumber, or gasfitter qualified 
or licensed by the State.

• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not 

exceed 4 feet.

FOR GAS DRYERS ONLY

2 Strainer Screens/ 

Rubber Washers

2 Washer Hoses

1 Cable Tie

234D2665P001

31-16781-3

  

08-18  GEA

Unitized Washer/Dryer

 

 

 

 

 

     01

Installation 

Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

 

 Save these instructions for local electrical 

inspector’s use.

IMPORTANT

 –

 Observe all governing codes and 

ordinances.

• Install the appliance according to the manufacturer’s 

instructions and local codes.

• Note to Installer –

 Be sure to leave these instructions 

with the Consumer.

• Note to Consumer –

 Keep these instructions for future 

reference.

• Appliance installation must be performed by a qualified 

installer.

• This dryer 

must

 be exhausted to the outdoors.

• Before the old appliance is removed from service or 

discarded, remove the washer and dryer doors.

• Do not allow children on or in the appliance. Close 

supervision of children is necessary when the appliance 
is used near children.

• Proper installation is the responsibility of the installer. 
• Product failure due to improper installation is not 

covered under the Warranty.

• Install the appliance where the temperature is above 50°F 

for satisfactory operation of the appliance control system.

• Remove and discard existing plastic or metal foil duct 

and replace with UL-listed duct.

• Service information and the wiring diagram are located 

at the access panel.

NOTE:

 The Rubber 

Washers may be in 

the water hoses

Summary of Contents for GUD27GSSM2WW









































Reviews: