![background image](http://html1.mh-extra.com/html/karcher/k2-winner/k2-winner_manual_4691509007.webp)
1. Switch off the appliance.
2. Unplug the power cable.
Cleaning the sieve in the water connection
regularly
Note
Do not damage the sieve.
1. Remove the coupling from the water connection.
2. Pull the sieve out.
Illustration K
3. Clean the sieve under running water.
Illustration L
4. Reinsert the sieve into the water connection.
Transportation
Note
Consider the weight of the appliance when storing it.
Lift up the appliance by the carrying handle, and car-
ry it.
When transporting the appliance in vehicles, secure
the appliance against shifting and tipping over.
Storage
Note
Consider the weight of appliance when storing it.
Prior to extended storage periods (for example, during
the winter), also observe the instructions in the care and
maintenance section.
1. Place the appliance on an even surface.
2. Lock the spray lance into its compartment.
3. Attach the power cable and the remaining accesso-
ries to the appliance.
Frost protection
Note
Completely drain the appliance and accessories, and
protect the appliance and accessories against frost.
1. Completely drain all water from the appliance:
a Switch on the appliance with the high-pressure
hose and water supply disconnected (max. 1
minute).
b Switch off the appliance until no more water exits
at the high-pressure connection.
2. Store the appliance and all accessories in a frost-
free room.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Troubleshooting
Before doing any work on the appliance:
1. Switch off the appliance.
2. Unplug the power cable.
Appliance is not running
1. Pull on the lever of the trigger gun to switch the ap-
pliance on.
2. Check whether the voltage indicated on the type
plate corresponds to the voltage of the mains sup-
ply.
3. Check whether the power cable is damaged.
Appliance does not start, motor hums
Voltage reduction due to weak power supply or when
using an extension cable.
1. When switching on the appliance, pull the lever of
the trigger gun, and then switch on the appliance.
Appliance does not have sufficient pressure
1. Check the water supply for adequate delivery rate.
2. Pull out the sieve from the water connection using
flat-nose pliers, and clean the filter under the run-
ning water.
3. Appliance ventilation:
a Disconnect the high-pressure hose.
b Switch the appliance on, and operate the appli-
ance (max. 2 minutes) until the water exits the
high-pressure connection without bubbles.
c Switch the appliance off.
d Reconnect the high-pressure hose to the appli-
ance.
Strong pressure fluctuations
1. Clean the high-pressure nozzle:
a Remove the dirt / dust from the nozzle bore using
a needle.
b Apply water to the front of the nozzle bore to rinse
it through.
2. Check the water flow quantity.
Appliance is leaking
Slight leakage from the appliance pump is normal. If
the leakage increases, please contact the next au-
thorised customer service site.
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Summary of Contents for K2 Winner
