background image

      

 

English  13

n

     Before cleaning any surface an inconspicuous  

area should be cleaned to test spray pattern 

and distance for maximum cleaning results.

n

     If painted surfaces are peeling or chipping,

 

  use extreme caution as pressure washer may 

remove the loose paint from the surface.

n

     When using on surfaces which might come in 

contact with food, flush surfaces with plenty 

of drinking water.

n

     For additional cleaning tips, visit our website 

at karcher.com/us

Recommendations

CLEANING TIPS

Optional accessories are available to further 

enhance your cleaning capabilities. These acces-

sories are accurate as of the printing date of this 

manual. Please check our website:  

 

karcher.com/us for pricing and up-to-date informa-

tion.

–  

Extension Hose

–  

Turbo Nozzle

–  

15-Inch Surface Cleaner, 3200 PSI

Optional Accessories

 CAUTION

Remove the spark plug cable to prevent accidental 

ignition of the engine before making any repair.

TROUBLESHOOTING

Symptom 

Cause

Solution

ENGINE WILL NOT 
START

No gasoline

Fill gas tank

Choke is not in the correct 
position

Slide choke lever out to closed position

Water pressure built up in 
the machine

Squeeze the trigger to release the pressure

For additional engine problems refer to the engine manual.

NOT ENOUGH 
PRESSURE

Diameter of garden hose is 
too small

Replace with a 5/8 inch or larger garden hose

Water supply is restricted

Check garden hose for kinks, leaks and
blockage

Not enough inlet water 
supply

Turn water on full force. Check garden hose
for kinks, leaks or blockage.

Water inlet filter is clogged

Remove filter and rinse out in warm water

Black detergent nozzle is 
attached

Remove black detergent nozzle and attach
high pressure nozzle

OUTPUT PRES-
SURE
VARIES HIGH AND 
LOW

Not enough inlet water 
supply.

Turn water on full force. Check garden hose
for kinks, leaks or blockage

Pump is sucking air

Check that hoses and fittings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady flow of
water emerges through the nozzle

Water inlet filter is clogged

Remove filter and rinse out in warm water

Spray nozzle is obstructed

Blow out or remove debris with a fine needle

Calcified gun, hose or 
spray wand

Run distilled vinegar through detergent 
suction tube.

Summary of Contents for G 3200 XK

















Reviews: