background image

8  English

OPERATING INSTRUCTIONS

  

STEP 1:

 

 

  Pull the spring-loaded collar of the wand back 

to insert your choice of quick connect nozzle.

 

  Release the collar and push the nozzle until-

the collar clicks.

  

CAUTION

 

  High pressure in nozzle area.

 

  Risk of injury caused by improperly locked 

nozzle.

n

    Make sure you hear a "click" when inserting 

the nozzle tip in to the wand.

n

    Pull the nozzle to make sure it is seated 

properly before operating your unit.

  

STEP 2:

 

 

  Attach the high pressure hose to the trigger 

gun.

 

 CAUTION

 

  Engine shipped without oil. Before starting 

engine, fill with oil. Do not over-fill. Do not run 
the engine with a high or low oil level as this 
can cause engine damage.

 

  If you have further questions regarding the 

engine, please refer to the engine manual 
included with the unit.

 

 

STEP 3:

 

  Check oil level. Oil level should always be 

between the "FULL" and "ADD" or "MAX" and 
"MIN" marks on the dipstick as shown in the 
picture below.

FULL / MAX

ADD / MIN

 

  Be sure the machine is level when checking 

the oil level. (Refer to the engines operating 
manual for seasonal grades).

 

  We recommend that the oil be changed after 

the first 5 hours of use, then once every 50 
hours.

  

STEP 4:

 

  Fill gas tank with unleaded gasoline.

 

  Do not use leaded gasoline.

 

  Do not add oil to the gasoline.

  

STEP 5:

  

Connect the high pressure hose to the high 
pressure outlet on the pump

.

  

STEP 6:

 

  Connect garden hose to unit's water inlet.

  

STEP 7:

 

  Connect garden hose to the cold water source 

and turn water completely on.

 

  Do not use hot water.

  

STEP 8:

 

  Unlock the trigger gun safety lock. Trigger the 

gun to eliminate trapped air, wait for a steady 
flow of water to emerge from the spray nozzle.

  

STEP 9:

 

  Move throttle to choke position (RUN position 

on a warm engine)

  

STEP 10: 

  

Open fuel valve

  

CAUTION

 

  High pressure in nozzle area. Risk of injury 

caused by improperly locked nozzle.

n

  Make sure you hear the "click" when inserting 

the nozzle tip into the quick connection.

n

    Pull the nozzle to make sure it is seated 

properly before operating your  unit. (See 

OPERATING INSTRUCTIONS: Step 1)

  

WARNING

 

  To avoid serious injury never point spray  

nozzle at yourself, other persons or animals.

Summary of Contents for G 3200 XK

















Reviews: