background image

OPERATION 

When the initial startup is complete, operating your CDG Series dispenser is simple. 

 

Place cup under the product tube. 

 

Push lever down for the desired quantity and product. 

 

Load product as needed. 

 

Perform preventative maintenance as outlined. 

MAINTENANCE 

Though the preventative maintenance of your CDG Series dispenser is minimal, these few steps 
are important for continued operation to maximize the life of this appliance. 

RECOMMENDED PREVENTATIVE MAINTENANCE SCHEDULE 

Drip Tray 

Daily 

Wash using warm, soapy water or in 
dishwasher. 

Exterior Cabinet 
Surfaces 

Daily 

Using a soft cloth, wash using warm, soapy 
water.  DO NOT use abrasive cleaners. 

Refrigerated Interior 
Compartment 

Each time product is 
loaded. 

Using a soft cloth, wipe down and thoroughly 
dry to remove any condensation.   

 

Monthly, or as needed.  Manually defrost when there is ice build-up. 

Valve Assembly and 
Area 

Monthly, or as needed. 

Wash using warm, soapy water or in 
dishwasher. 

Condenser 

Every six (6) months. 

Clean using vacuum. 

DEFROST 
The CDG Series dispensers are equipped with an automatic defrost cycle to minimize frost 
build-up.  The defrost cycle reduces but does not eliminate the need for a manual defrost.  
Frost or ice will reduce the system efficiency.  When frost or ice is build-up is excessive: 

 

Remove product from the dispenser. 

 

Turn the power control switch OFF. 

 

With the compartment door open, wait 15 minutes for ice to melt. 

 

Remove ice gently, and wash using warm, soapy water. 

 

Thoroughly dry with a soft cloth, and close the compartment door. 

 

Turn the power control switch ON. 

 

When proper operating temperature is achieved, load pre-chilled product. 

RESET 
Occasionally, it may be necessary to reset the control system.  To accomplished this, simply: 

 

Turn the power control switch OFF. 

 

Wait 5 seconds to reset the microprocessor. 

 

Turn the power control switch ON.  

Page 6

Summary of Contents for CDG-211





















Reviews: