background image

- Data Brochure

Mixing Control 362e

D 362e

06/03

 

1 of 32 

© 2003          D 362e - 06/03

The  Mixing  Control  362e  is  a  microprocessor  based  control  designed  to  provide  a  reset  mixed  supply  water  temperature  to 
a  heating  system  based  on  outdoor  air  temperature.  Multiple  zone  temperature  control  can  be  achieved  by  using  either  a 
conventional thermostat system or by using kanmor Zone Controls attached to the 362e. For single zone heating applications, a 
single Room Temperature Unit (RTU) can be connected directly to the 362e for zone temperature control.

The 362e incorporates a large Liquid Crystal Display (LCD) in order to provide system status and operating information. The 
same LCD is used when setting up and installing the control. Standard features include boiler return protection, intelligent boiler 
operation, Warm Weather Shut Down (WWSD), and pump exercising. As well, with the addition of a new Monitor feature, it is now 
possible to track pump and boiler running hours, boiler cycles and high and low sensor temperatures.

The 362e uses a floating action output signal to control the position of a mixing valve.

Output

Mixing Valve &

Actuating Motor

Output

Boiler

Output

Mixing

System

Pump

M

Input

230 V (ac)

Power

Supply

Input

Outdoor
Sensor

Included

Input

Universal Sensor

Included

Input

Universal Sensor

Included

Input

Mix 

Demand

signal

Input

kanmor

timer

Input

Room

Temperature

Unit (RTU)

Input

Remote

Display

Module (RDM)

OR

H1

1XXA

N

L

Pmp

tN2

Sw

Mix

tN1/ Com 10K UnO Com Mix

Boil Out

1

2

Mix

Pwr Opn Cls

10

3

4

5

6

7

8

9

11 12 13 14

16

15

17 18

Mixing Control 362e

Floating Action

Do not apply power

Signal wiring must be rated at least 300 V.

Power

Mix

Demand

Boiler

Menu

Item

Mix Demand

WWSD

Minimum

Maximum

Test

off 

not testing

red 

testing

red 

testing paused

For maximum heat,
press and hold 

Test

button for 3 seconds

Setback

None

INSTALLATION CATEGORY II
Made in Canada  

Power: 

230 V ±10% 50/60  Hz 2300 VA

Relays: 

230 V (ac) 10 A 1/3 hp, pilot duty 240 VA

Demand: 

20 to 260 V (ac) 2 VA 

Input

kanmor Slab Sensor, or

Indoor Sensor or Zone Control

OR

OR

Summary of Contents for Mixing Control 362e

































Reviews: