background image

 

 

 

 

Braking Pedal 

Braking pedal is operated 

by left foot. It will work 

when step hard forward 

and the off-road kart will 

slow down.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gas Pedal 

 

Gas pedal is operated by 

right foot. It will accelerate 

when step hard forward 

and slow down otherwise. 

 

 

 

 

 

 

 

 

 

 

Gear-engaging Device 

 

 

 

If there is gear-

engaging device in your kart, 

you must make clear the 

function and operating 

ways of each gear so that 

you can avoid the danger 

arising from the 

unexpected running.  

 

The reverse gear 

controller for this kart is 

between the seats.  

 

The gear-operating 

ways for the engine are as 

follows: 

-

 

Move the handle 

backward and locate 

the gear pole at the 

back gear, the kart will 

go backward.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: 

You must keep the hands on steer 

wheel to avoid the losing control of the kart 

when driving the off-road kart. Otherwise it 

may cause serious accidents even death.  

WARNING: 

You must be skillful in the operation and 

the force braking pedal and gas pedal when driving 

initially off-road kart so that you can control the 

speed properly especially in the curves and among 

the karts.  

 

 

ATTENTION: 

you must stop when 

conduct gear changes.  

Summary of Contents for 150GKA-2 Series

















Reviews: