background image

11

Care, Cleaning and Storage

Emptying the Dust Canister

Always switch the handheld vacuum 

cleaner ‘OFF’ before emptying  

the dust canister. For optimum use,  

the dust canister should be emptied  

after every use.

To empty the dust canister;

1.  To empty the dust canister, 

while holding the handle of 

the handheld vacuum, press 

downwards with your thumb on 

the release button located at the 

top of the handle. Use your other 

hand to pull the dust canister 

away from the handheld vacuum 

pointing the nozzle downwards to 

avoid spillage (see Fig.9).

2.  Tip the dust canister into the 

rubbish bin, lightly tapping  

the sides if necessary to  

dislodge debris.

3.  Hand wash the dust canister with 

warm soapy water if required. 

4.  Ensure the dust canister is dried 

completely before refitting to the 

handheld vacuum.

To Clean the Inlet Valve

The handheld vacuum is fitted with 

an inlet valve. After emptying the 

dust canister, the inlet valve may be 

cleaned to remove excess dust and 

debris that has built up after usage.
Care must be taken when removing 

the inlet valve from the handheld 

vacuum.
1.  Hold the dust canister in one 

hand and take hold of the fitted 

inlet valve with the other hand 

pulling the inlet valve firmly away 

from the dust canister.

2.  Hand wash the inlet valve with 

warm soapy water if required.

3.  Ensure the inlet valve is dried 

completely before refitting to the 

handheld vacuum.

4.  To refit the inlet valve to the dust 

canister, with the inlet valve 

rubber flap facing outwards to 

the right, hold the dust canister in 

one hand and take hold of the 

inlet valve and push into place 

until secured (See Fig.10).

Fig. 9

Fig. 10

Summary of Contents for Captiv 12V Turbo

















Reviews: