background image

46

GB

Fireplace flue gas

Avoid contact with combustible materials (example: 
wooden beams) and in any case provide for their insulation 
with flame retardant material. In case of pipe penetrations 
through roofs or walls is recommended to use special 
kits crossing, certificates, are available commercially. In 
the event of a chimney fire, turn off the stove, disconnect 
from the network and never open the door. Then call the 
authorities.

The chimney cap

The chimney cap must respect the following requirements: 
• It must have the equivalent diameter and internal form
of the flue. 
• It must have a useful outlet diameter of not less than 

double that of the flue. 

• The chimney cap on the roof or that remains in contact 

with the outside (for example, in case of open lofts or 
attics), must be covered with elements in brick or tile 
and must, in any case, be well insulated.

• It must be constructed to prevent rain, snow, and 

extraneous bodies from entering the flue and so that 
the discharge of the products of combustion is not 
inhibited by wind from any quarter or strength (wind-
proof chimney cap).

• The chimney cap must be positioned in such a way as 

to guarantee the adequate dispersion and dilution of the 
products of combustion and in any case, must be out of 
the reflux zone. This zone has different dimensions and 
forms according to the angle of inclination of the roof so 
it is necessary to adopt minimum heights (Fig. 2). 

• The chimney cap must be a wind-proof type and must 

be above the ridge.

•  Eventual structures or other obstacles that are higher 

than the chimney cap must not be too close to the 
chimney cap itself. 

Fig. 5: Characteristics of chimney

YES

NO

REMARKS:

- the appliance must be installed by a qualified technician in 
possession of the technical and professional requirements 
according to the DM37/2008 that, under its responsibility, 
to ensure compliance with the rules of good technique.
- the thermostove must be connected to a heating system 
and/or to a network of production of sanitary hot water, 
consistent with its performance and its power
- you need to keep in mind all laws and national, regional, 
provincial and municipal laws of the country in which you 
installed the device
- check that the floor is not flammable: if necessary use a 
suitable platform
- in the room where the generator must be installed to 
heat must not pre-exist or be installed with an extractor 
hood or ventilation ducts of the collective type.
Should these devices be located in adjacent rooms 
communicating with the installation, and ‘prohibited the 
simultaneous use of the heat generator, where there is a 
risk that one of the two rooms being placed in depression 
than the other
- it is not permissible to install in bedrooms or bathrooms
- for hydraulic connections (see next chapter) it is advisable 
to use where possible of hoses

Distance to objects

The thermostove should be inspected on all sides, so you 
have to keep a distance of at least 40 cm at the back and 
sides. It is also recommended to keep the pellets and all 
flammable materials at a suitable distance

40 cm

100 cm

40 cm

Summary of Contents for 24B





















Reviews: