Kalor 24B User Manual Download Page 4

42

GB

Our company declares that the stove conforms to the fol-
lowing norms for the EC European Directive labelling:
• 

2014/30 UE (regulation EMCD) and following 

 

amendments;

• 2014/35 UE (Low Voltage Directive) and following 

amendments;

• 2011/65 UE (RoHS 2 directive);
• The New Rules of Construction Products (CPR-Con-

struction Products Regulation) No. 305/2011 regarding 
the construction world;

• For installations in Italy, please refer to UNI 10683/98 or 

following changes. For the water-thermo-sanitary equip-
ment, let the installer give you the conformity declaration 
in compliance with L. 37/2008. While installing the unit 
respect the local, national and Europen rules;

• EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; 

EN 60335-1; EN 60335-2-102; EN 62233, EN 50581.

Safety information

Please carefully read this use and maintenance manual 
before installing and operating the stove! 
If clarification is needed, please contact the dealer or the 
Authorized Assistance Center.
• The pellet stove must only be operated in living envi-

ronments. This stove, being controlled by an electronic 
board, permits a completely automatic and controlled 
combustion; the exchange, in fact, regulates the lighting 
phase, 5 power levels and the shut down stage, guaran-
teeing the safe operation of the stove.

• The basket used for combustion allows most of the ash 

produced by the combustion of the pellets to fall into 
the collection compartment. Nevertheless, check the 
basket daily, given that not all pellets have high qual-
ity standards (use only quality pellets recommended by 
the manufacturer).

Responsibility

With the delivery of the present manual, we decline all 
responsibility, both civil and penal, for accidents deriving 
from the partial or total lack of observance of the instruc-
tions contained herein.
We decline every responsibility derived from improper 
use of the stove, from incorrect use by the user, from un-
authorized modifications and/or repairs, from the use of 
replacement parts that are not original for this model.
The manufacturer declines every civil or penal, direct or 
indirect responsibility due to:
• Lack of maintenance;
• Failure to observe the instructions contained in the 

manual;

• Use in non-conformity with the safety directives;
• Installation in non-conformity with the norms in force in 

the country;

• Installation by unqualified or untrained personnel;
• Modifications and repairs not authorized by the 

manufacturer;

• Use of non-original replacement parts;
• Exceptional events.

Norms and declarations of conformity

• Use only wood pellets;
•Keep / store the pellets in a cool dry 

place;

• Never pour pellets directly on the hearth;
• The thermostove must only be fed with quality 

6 mm diameter pellets of the type recommend-
ed by the manufacturer;

• Before making the electrical connection of the 

thermostove the discharge tubes must be con-
nected with the flue;

• The protective grill placed inside the pellet con-

tainer must never be removed;

• The environment where the stove is installed 

must have a sufficient exchange of air;

• It is forbidden to operate the thermostove with 

the door open or the glass broken;

• Do not use the thermostove as an incinerator; 

the thermostove should be used only for the in-
tended purpose;

• Any other use is considered improper and 

therefore dangerous. Do not put in the hopper 
other than wood pellets;

• When the thermostove is operating, the surfac-

es, glass, handle and tubes become very hot: 
during operation do not touch these parts with-
out adequate protection;

• Keep the fuel and other inflammable materials 

off the thermostove.

Summary of Contents for 24B





















Reviews: