- Six hex keys in different sizes (2 to 8 mm)
- 16 mm open-end wrench
- Box of spindle grease
- 1/4“ camera mounting screw
Additionally with RSP 2motion Copy Stand (5710):
- Column foot (6) with base (5)
- Four M8x100 fixing screws with A8.4 washers, for attach-
ing the base (5) to the column foot (6)
1.2 RSP Xtra Copy Stand (5711) and Column (5709)
- Column (1) with camera carrier (3) and dead stop (35)
- Control box (11a) and cable remote control (19) for camera
carrier (3)
- Mains lead for control box (11a)
- Four M8x100 screws with A8.4 washers, for fastening the
column (1) in the base (5)
- Five hex keys in different sizes (2 to 6 mm)
- Box of spindle grease
- 1/4“ camera mounting screw
Additionally with RSP Xtra Copy Stand (5711):
- Column foot (6) with base (5)
- Four M8x100 fixing screws with A8.4 washers, for attach-
ing the base (5) to the column foot (6)
Please check, if the devices are damaged by extraneous
causes. If this is the case, do not take the devices into opera-
tion.
2. Assembly
Please note: If parts have to be fastened with several screws,
you must
first loosely screw in all screws
before tightening
them.
RSP 2motion and RSP Xtra
Columns
(5708/09):
The column (1) can be attached to a wall with a load-bear-
ing capacity using the rePRO wall mount (5614) or can be
mounted in the rePRO base (5610) on a suitable substruc-
ture.
RSP 2motion and RSP Xtra
Copy Stands
(5710/5711):
Attach the base (5) to the column foot provided (6) (fig. C).
Then fasten the column (1) in the base (5) of the column
foot:
Insert the column (1) into the base (5) from the rear so that the
two pins in the base are inserted in the corresponding holes in
the column. Attach the column to the base (fig. D). Check if
the column is firmly attached to the base.
If applicable, move the copy stand with mounted column foot
to its destined position and align the column (1) vertically with
the help of the height-adjustable feet (7) and a spirit level.
2.1 RSP 2motion Copy Stand (5710) and Column (5708)
Slide the support struts (39) of the base board (4) from the
front onto the side guides (43) of the lower carriage (2b) (fig. E)
and fasten them on each side with two screws (40) with wash-
ers (fig. F). (It may be necessary that a second person lifts the
base board slightly at the front edge).
Then loosen the two fixing screws (42) with the 6 mm hex key
and rotate the two eccentrics (41) with the 16 mm open-end
wrench until the eccentrics are in contact with the underside
of the side guides (43). Subsequently retighten the two fixing
screws (42).
Control boxes (11a, 11b) for the carriages are marked “A” (for
camera carrier carriage) and “B” (for the base board carriage).
Connect the supply cables (9a) and (9b) to the respective
sockets (15) of the control boxes (11a) and (11b) (connect A to
A and B to B). Then connect the (identical) cable remote con-
trols (19) to the sockets (14) of both control boxes.
2.2 RSP Xtra Copy Stand (5711) and Column (5709)
Connect the supply cable (9a) to the socket (15) of the control
box (11a) and the cable remote control (19) to the socket (14).
3. Initial operation
Check that the mains voltage corresponds to the operating
voltage given on the type plate(s) of the control box(es) (11a,
11b). Then connect the control box(es) with the mains lead(s)
to the mains.
Switch on the control box(es) with switch (13). The switch will
light up red.
4. Attaching the camera
The camera carrier (3) is suitable for all photographic, profes-
sional, film, video and television cameras up to a weight of 10
kg (22 lbs.) (RSP 2motion) resp. 15 kg (33 lbs.) (RSP Xtra).
Fasten the camera by means of the mounting screw to the
camera carrier (3).
The standard fitted 3/8“ mounting screw can be replaced by
the 1/4“ mounting screw included. To do this, undo the screw
(26) (e.g. with a coin) and replace the 3/8“ screw by the 1/4“
screw.
The mounting screw can be fitted in three different height po-
sitions (28a, 28b, 28c) on the camera carrier (3).
Undo the locking screw (25) to move the camera sideways.
To adjust and tilt the camera, the camera carrier (3) can be tilt-
ed upwards and downwards by a maximum of 90° and fixed
in any position. Proceed as follows: Secure the position of the
camera with your hand and loosen the locking screw (31).
Align the camera. Use the fine adjustment handle (38) for sen-
sitive adjustment. Then retighten the locking screw (31). The
vertical position of the camera carrier (3) can be checked with
the aid of the spirit level (27) on the camera carrier, and fixed
to stop accidental movement by tightening the fixing screws
(32). This is done with the 4 mm hex key.
5. Height adjustment
The height of the camera carrier (3) and the base board (4)
(RSP 2motion only) is adjusted by a motorized drive and con-
trolled by the cable remote (19). To move upwards and down-
wards at low speed, press button
s
(16) or
▼
(18). For high
speed
also
press button (17). The bottom of the cable re-
mote(s) has a magnetic surface and thus adheres to the base
board of 2motion (5710/5708), for example.
The column is equipped with a movable dead stop (35) that
serves as a lower stop for the camera carrier carriage (2a) or
an upper stop for the base board carriage (2b) of RSP 2mo-
tion. Release the blocking screw (36) prior to moving the dead
stop and tighten it again.
6. Horizontal adjustment of the camera carrier
Turn the adjusting cranks (30) to set the camera carrier hori-
zontally. You can lock the position with the blocking screws
(29).
5710_Bedien_Sondervariante_1123.qxp_5710_Bedien 07.11.23 14:06 Seite 10
