background image

6

KABA SIMPLEX

®

LIMITED WARRANTY

Kaba Access Control warrants this product to be free from defects in material

and workmanship under normal use and service for a period of one (1) year.

Kaba Access Control will repair or replace, at our discretion, locks found by Kaba

Access Control analysis to be defective during this period. Our only liability,

whether in tort or in contract, under this warranty is to repair or replace

products that are returned to Kaba Access Control within the one (1) year

warranty period.

This warranty is in lieu of and not in addition to any other warranty or condition,

express or implied, including without limitation merchantability, fitness for

purpose or absence of latent defects.

ATTENTION: This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and / or if any supplied component part is

substituted with a foreign part. If the lock is used with a wall bumper, the

warranty is null and void. If a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes on Kaba

Access Control products. Finishes on Kaba Access Control products are subject

to change due to wear and environmental corrosion. Kaba Access Control cannot

be held responsible for the deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization Numbers (RGA Numbers) are available

through our Customer Service department in Winston-Salem, NC 800.849.8324.

The serial number of a lock is required to obtain this RGA Number

. The

issuance of an RGA does not imply that a credit or replacement will be issued.

The RGA number must be included on the address label when material is

returned to the factory. All component parts including latches and strikes (even

if not inoperative) must be included in the package with return. All merchandise

must be returned prepaid and properly packaged to the address indicated.

Summary of Contents for Simplex 3000 Series













Reviews: