manualshive.com logo in svg

Kaba RAC 4, Installation Manual, Page: 16 / 36

Share
Download
Kaba RAC 4 Installation Manual Download Page 16

INSTALLATION GUIDE - REMOTE ACCESS CONTROLLER RAC 4 • PK3197_10_14

For 

Contactless card readers:

 present 

a new initialization keycard, programmed 
by the new FDU/ATLAS System, to the 
contactless reader. The green LED on 
the contactless reader should turn off in 
sequence: rapid twice, followed by normal 
once. Alternatively the controller board (B) 
can be verified to ensure that LED D41 is 
on.

5.4 Programming and Auditing

IMPORTANT:

Programming of the RAC 4 can only 
be done with the following versions of 
programming device software:

- ATLAS: software version 1.0 or higher
-  

Kaba Ilco 780 FDU: software version 
6.40 or higher

- Kaba Ilco FDU 4 (G4): all versions

The RAC 4 can be programmed using either 
an FDU or ATLAS system. Refer to the 
appropriate steps below based on the hotel’s 
programming system.

NOTE:

  

-   

If a Remote Programming Interface 
(RPI) is connected the RAC 4 can be 
programmed directly via the connector in 
the RPI.

-   

Unlike Kaba’s electronic locks a 
Programming keycard is not required 
for the RAC 4 as the system is already in 
programming mode.

FDU Programming

1.   Link the FDU to the DB1 in the RPI box, or 

to the DB9 connector (serial port J5) on 
the controller PCB. Refer to figure 20 for 
the positions of the relevant connectors.

2. 

 

For step-by-step programming 
instructions refer to the Kaba Ilco Lodging 
Access Control Reference Manual.

ATLAS Programming

For ease of programming the IPM kit for RAC 
(PN 064-511161) can be used by attaching the 
IPM to the RAC with the Velcro provided in 
the kit.

- 

 Cut a piece of each type of Velcro from 
the strip provided.

-   

Depending on the configuration of the 
system attach one side of the Velcro to 
either the side of the RPI, or to the side of 
the RAC 4 enclosure.

- 

 Attach the other side to the side of the 
IPM.

1.   Connect one side of the DB-9 serial cable 

to the IPM.

2.   

Connect the other side to the DB-9 
connector (serial port J5) on the controller 
PCB of the RAC 4.

3. 

 

For step-by-step programming 
instructions refer to the ATLAS on-line help 
or the ATLAS Administration manual.

Figure 20 

Page 15

DB9 Cable

FDU

RAC 4

RAC 4

DB9 Cable

DB9 Cable

IPM

DB9 Cable

RPI

FDU

Summary of Contents for RAC 4





































Reviews:

No comments