background image

 6 •

  

TEST THE OPERATION OF THE 

E-760/770/790 LOCK

PK2915-T 07_2014 E-760/770/790 SERIES RETROFIT INSTALLATION GUIDE

Page 9

Turn the 

inside

 lever downward. The latch bolt retracts fully. 

If the lever feels tight

 (hard to turn, or does not return easily to its 

horizontal position), check the alignment of the lock assemblies. Loosen 
the mounting screws and shift the inside trim assembly slightly until the 
friction is eliminated. If the problem persists, check the position of the 
holes on the door (compared to the mortise). 

Turn the thumbturn back and forth. The deadbolt extends and retracts fully 
without undue friction.
Turn the thumbturn to extend the deadbolt again, then turn the 

inside

 

lever. The deadbolt and the latch bolt retract simultaneously and fully 
without undue friction.

Turn the 

outside

 lever downward. The latch bolt does not retract.

If the latch bolt retracts,

 verify that the batteries are properly 

installed.

If the lever feels tight

 (hard to turn, or does not return easily to its 

horizontal position), check the alignment of the lock assemblies. Loosen 
the mounting screws and shift the outside housing slightly until the friction 
is eliminated. If the problem persists, check the position of the holes on 
the door (compared to the mortise), and ensure the square spindle is not 
too long.

Test the lock’s response to keycards: a Test keycard, a Grand Master 
keycard, and an Emergency keycard. 
Insert keycards as shown below, with the magnetic stripe facing toward 
the door and to the left.

Inside Lever

2 Deadbolt

Outside Lever

 Test the Lock Before Programming

Normal Entry: 

Verify that the deadbolt is retracted. Use the Test key-

card in the reader. The 

red

 and 

green

 LEDs each flash once and then the 

green

 LED flashes for four seconds. 

Turn the 

outside

 lever downward while the 

green

 LED is flashing. The 

latch retracts fully. Release the lever, then turn it again after the LED stops 

flashing. 

The latch must not retract after the LED stops flash-

ing without first inserting the keycard.

Privacy Switch: 

Turn the thumbturn to the horizontal position. (On 

storeroom models, skip this test.) Use the Test keycard in the reader, but 

do not turn the lever. Instead of the normal sequence of indicator lights, 

you should see the following: The 

red

 and 

green

 LEDs each flash once 

and then the 

green

 LED flashes once, followed by the 

red

 LED flashing 

continuously for four seconds. 

If you see the flashing green LED, 

there is a problem with the privacy switch.

 Lock Programming

Program the lock with its room number (see Reference Manual).
Verify that the deadbolt is retracted, and use the Grand Master keycard in 

the reader. The 

green

 LED flashes for 4 seconds. Turn the 

outside 

lever 

downward while the 

green

 LED is flashing. The latch retracts fully. Release 

the lever, then turn it again after the LED stops flashing.

 The latch must 

not retract after the LED stops flashing without first insert-

ing the keycard.

 Privacy Function (Lockout of Keycards)

Turn the thumbturn to the horizontal position for privacy.
Use the Grand Master Keycard in the reader. The 

red

 

LED flashes once. 

Then, turn the outside lever downward. 

The latch does not retract.

D  

Emergency Keycard Access (Privacy Override)

Use the Emergency keycard in the reader. The 

red

 LED flashes for 4  

seconds. Turn the 

outside

 lever downward while the LED is flashing. 

The 

deadbolt and latch bolt retract simultaneously and fully.

While standing outside the room, close the door and ensure that it is 

properly latched. Open the door using the Grand Master keycard using the 

same procedure.

Deadbolt Deactivation by Thumbturn

While standing inside the room, close the door, and then turn the thumb-

turn to extend the deadbolt. 
Turn the thumbturn to retract the deadbolt.

 Repeat several times.

B.  

Deadbolt Deactivation by Lever

While standing inside the room, turn the thumbturn to extend the deadbolt.
Open the door by turning the lever. The deadbolt and the latch bolt retract 

simultaneously and fully. Take note of any excess friction, which might 

necessitate filing the strike (deadbolt area only). 

Repeat several 

times.

Electronics and Card Reader

Deadbolt Deactivation

Caution! Perform the following procedures in order, 
with the door OPEN unless otherwise indicated.

!

Summary of Contents for ILCO Generation E-760 Series





















Reviews: