background image

3

Procedure 11 - Activate All User Access Codes . . . . . . . . . . . . . . . . . . . . . . .24

Procedure 12 - Activate / De-activate Passage Mode . . . . . . . . . . . . . . . . .24

Procedure 13 - De-activate User Access Codes . . . . . . . . . . . . . . . . . . . . . .25

Procedure 14 - De-activate Manager Access Codes . . . . . . . . . . . . . . . . . . .25

Procedure 15 - De-activate Service User Access Code . . . . . . . . . . . . . . . .26

Procedure 16 - De-activate all Access Codes except20

Master, Manager, and M-Unit

Procedure 17 - Activate / De-activate Lockout Mode . . . . . . . . . . . . . . . . .26

Procedure 18 - Perform Manual Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . .27

Battery Life and Replacement . . . . . . . . . . . . . . . . . . . . . . . .27

Procedure 19 - Latch Holdback Operation . . . . . . . . . . . . . . . . . . . . . . . . . .28

(E-Plex 30xx Series Only)

Procedure 20 - Swing Bolt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

(E-Plex 30xx Series Only)

Summary of Pushbutton Programming Commands . . . . . . . . . . . . . . . . . . . . . . .31

Visual Feedback Message Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

User List Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

TABLE OF CONTENTS

(continued)

A publication of Kaba Access Control
2941 Indiana Avenue
Winston-Salem, NC 27105

No part of this book may be reproduced or
transmitted in any form or by any means,
electronic or mechanical, including photocopying,
recording, or by any information storage and
retrieval system, without prior written permission
from the Publisher.

The information contained in this publication
is accurate to the best of Kaba Access
Control’s knowledge.

Specifications are subject to change
without notice.

Legend

• “E-Plex Lock” refers to both the E-Plex 5000 and the E-Plex 3000 locks.
• “E-Plex 5000” refers to the E-Plex 5000 series locks only.
• “E-Plex 3000” refers to the E-Plex 3000 series locks only.

Summary of Contents for E-PLEX 30XX SERIES





































Reviews: