background image

Dewert User Manual Heavy-Weight Tables – Updated 11.2021/3 MDR                                                         Page 2 of 14 

1. Safety information 

 
1.1 Applied 

symbols 

Safety instructions and key sections in this user manual are marked with the exclamation mark symbol on the 
left. Please pay particular attention to these instructions and sections. 
 
Other symbols possibly used on the device: 

Observe instructions for use: 

 

 

Risk of pinching when adjusting:  

 

Risk of hazard zone: 

 

 

 

 

 

 

1.2 Applied standards 

 

This device has been designed and manufactured in accordance with national and international regulations. 
This ensures a very high level of equipment safety. 
The models described here comply with the following regulations and directives: 
 

Regulation (EU) 2017/745 
DIN EN IEC 60601-1 
DIN EN ISO 14971 
DIN EN 60601-2-52 partly based on 
DIN EN IEC 62353 
DIN EN ISO 10993-5/-10 
DGUV Regulation 3 

     
This device is a Class 1 medical device according to Regulation (EU) 2017/745 (MDR). 
 
 

1.3 Safety regulations

 

This section contains a summary of the most important safety information. 
 
Correct operation of the device is essential for safe operation. Therefore, please familiarise yourself with the 
contents of these instructions for use before using the device. We recommend that you keep these 
instructions for use near the device for future reference.  
The device may only be used by authorised, instructed and competent persons who are sufficiently familiar 
with its adjustment mechanism or have read and understood the operating manual fully. The manufacturer 
cannot be held responsible for damage caused by or involving unauthorised persons. No third-party devices 
may be installed without consultation with us or brought in the direction of movement of the table in such a 
way that a possible hazard potential arises. 

 

The user must ensure that the device is not accessible to unauthorised persons or cannot be operated by 
unauthorised persons even when left unattended. 
When leaving the device, it should be secured in such a way that unauthorised adjustment is impossible. 

Important:

 Never leave the device unattended or accessible to third parties when it is ready for operation. 

 

Keep a sufficient safety distance to the device during all adjustment procedures. Special attention 
must be paid to the arms, hands, legs and feet of the user and the patient - 

RISK OF CRUSHING!

 

 

 

Make sure that there are no objects located directly around or underneath the device! 

 

 

 

 

 

1.4 Intended purpose

 

The table is used for the ideal positioning of patients for the purpose of curative and disease treatment, 
examination, massage and health therapy. 

Summary of Contents for 208















Reviews: