JVC XV-C3SL Service Manual Download Page 22

Page: 22 / 81

XV-C3SL

4.5 Confirm method of operation

Please confirm the operation of the undermentioned item after doing the repair and
the upgrade of the firmware.

The EEPROM is initialized.

Refer to the initialization method.

Opening picture check (Power ON)

It should be display "JVC"

Muting working

The noise must not be had to the performance beginning when you push "PLAY" button or at ON/STANDBY.

FL Display

The mark and the logo, etc. displayed by each operation must be displayed correctly.
FL Display should light correctly without any unevenness.

All Function button

All function buttons should worked correctly with moderate click feeling.

Open and close movement of tray

When press OPEN/CLOSE button the tray should move smoothly without any noise.

Remote controller unit working

Check the correctly operation in use of remote controller unit.

Reading of TOC

Be not long in the malfunction.

Search

Both forward-searches and backward-searches should be able to be done.
Do not stop be searching or after the search.

Skip

Both forward-skip and backward-skip should be able to be done.
Do not stop be after the skip.

Playback

Do not find abnormality etc. of tone quality and the picture quality.

Most outside TITLE playback check

Play VT-501 TITLE 59 CHAPTER 1 , check normal playback.

Summary of Contents for XV-C3SL

















































































Search results

Summary of Contents for XV-C3SL

Reviews:

Related manuals for XV-C3SL

Brands by name

Popular brands

JVC XV-C3SL, Service Manual

Search results

Summary of Contents for XV-C3SL

Reviews:

Related manuals for XV-C3SL

Brands by name

Popular brands