JVC VN-V686WPU Instructions Manual Download

Page: 94 / 121

Settings and operation of Built-in Viewer

Installing Built-in Viewer

Enter the URL of Built-in Viewer in the address field of Internet Explorer

For example, if the IP address of VN-V686WPU is 192.168.0.2, enter as follows:

䡵

JPEG Viewer

http://192.168.0.2/cgi-bin/v686viewing.cgi?v686monitor_j.html

䡵

MPEG4 Viewer

http://192.168.0.2/cgi-bin/v686viewing.cgi?v686monitor_m.html

Enter the user name and password

The viewer is installed and launched

Preparation (continued)

http://192.168.0.2/cgi-bin/v686viewing.cgi?v686monitor_j.html

Enter the URL in Built-in Viewer of this camera.
(Refer to the above for the default URL setting.)

Click [Go]

Enter the user name.
This is set to

admin

by default.

Click [OK].

Enter the password.
This is set to

vn-v686

by default.

Summary of Contents for VN-V686WPU


























































































































Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands

JVC VN-V686WPU, Instructions Manual

Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands