JVC TM-A101G/E Service Manual Download Page 28

Page: 28 / 33

No. 51921

TM-A101G

DEFLECTION CIRCUIT ADJUSTMENT

There are 4 modes of DEFLECTION adjustment depending upon the kind of input signals.

The adjustments must always be carried out in regular sequence given below.

SIGNAL MODE

SERVICE NUMBER

SETTING VALUE

50Hz (PAL)

4:3

60Hz (NTSC)

+ DA

50Hz (PAL)

+ DB

16:9

60Hz (NTSC)

+ DA

+ DC

If you change the figures in the course of the adjustments by returning to the preceding steps, all adjustments come to nothing.

The screen aspect ratio 4 : 3 at 50Hz (PAL) is regarded as the reference value for all adjustments. The other values obtained in the

adjustments using other signals become the offset values as opposed to the reference values.

Item

Test equipment

Test points

Adjustment

locations

Adjustment procedure

H. Center

H. Size

Adjustment

Signal generator

(Crosshatch pattern)

D01 (H.POSITION)

[SERVICE MENU]

L502(H. SIZE COIL)

[MAIN PWB]

1. Input a PAL (50Hz) crosshatch pattern signal.

2. Select DEFLECTION BLOCK mode from

<BLOCK SELECT> screen.

3. Select

D01

item.

4. Adjust D01 to align the picture center with the

CRT center.

5. Adjust L502 to set horizontal size to

90%

6. Repeat above step 4 and 5 to adjust correctly.

V. Center

Adjustment

Signal generator

(Circle pattern)

S401

(V.CENTER SW)

[MAIN PWB]

7. Input the circle pattern signal.

8. Adjust S401 to agree with CRT center and signal

center of vertical direction.

90%

100%

SCREEN SIZE

PICTURE SIZE

100%

Summary of Contents for TM-A101G/E


































Search results

Summary of Contents for TM-A101G/E

Reviews:

Related manuals for TM-A101G/E

Brands by name

Popular brands

JVC TM-A101G/E, Service Manual

Search results

Summary of Contents for TM-A101G/E

Reviews:

Related manuals for TM-A101G/E

Brands by name

Popular brands