JVC SP-PWM508 Service Manual Download Page 28

Page: 28 / 89

1-28 (No.MB294)

3.4.4 Removing the heat sink bracket

(See Fig.5)

• Prior to performing the following procedure, remove the ampli-

fier assembly.

(1) From the top side of the amplifier assembly, remove the

three screws

and three screws

attaching the heat sink

bracket.

(2) Take out the heat sink bracket.

Reference:

When attaching the heat sink bracket, attach the screw

with

barrier.

Fig.5

3.4.5 Removing the amplifier board

(See Fig.6)

• Prior to performing the following procedures, remove the am-

plifier assembly and heat sink bracket.

(1) From the top side of the amplifier assembly, disconnect the

amplifier board from the connector

CN201

and

CN203

the main board.

(2) Take out the amplifier board and disconnect the wire from

the connector

CN202

on the amplifier board.

Fig.6

Heat sink bracket

Barrier

CN201

CN203

Amplifier board

Main board

CN202

Summary of Contents for SP-PWM508


























































































Search results

Summary of Contents for SP-PWM508

Reviews:

Related manuals for SP-PWM508

Brands by name

Popular brands

JVC SP-PWM508, Service Manual

Search results

Summary of Contents for SP-PWM508

Reviews:

Related manuals for SP-PWM508

Brands by name

Popular brands