JVC SP-PWM508 Service Manual Download Page 2

Page: 2 / 89

1-2 (No.MB294)

SPECIFICATION

Center unit (XV-THM508)

*1 : This value is measured at System cord CONNECTOR for reference.
*2 : Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency - 32 kHz, 44.1 kHz, 48 kHz)
*3 : For PAL system

Subwoofer (SP-PWM508)

Satellite Speakers-Front speakers (SP-THM508F)

Audio section Digital input*2

DIGITAL IN (DBS) (OPTICAL) -21 dBm to -15 dBm (660 nm E30 nm)

Video section Video System

NTSC/PAL selectable

Horizontal Resolution

500 lines

Signal-to-Noise Ratio

64 dB

Video output level

Composite

1.0 V(p-p)/75

Ω

S-video-Y

1.0 V(p-p)/75

Ω

S-video-C

0.286 V (0.3 V*3) (p-p)/75

Ω

Component-Y

1.0 V(p-p)/75

Ω

Component-PB/PR

0.7 V(p-p)/75

Ω

Video input sensitivity/
Impedance (VCR IN)

Composite

1.0 V(p-p)/75

Ω

S-video-Y

1.0 V(p-p)/75

Ω

S-video-C

0.286 V (0.3 V*3) (p-p)/75

Ω

Tuner section Tuning Range

87.50 MHz to 108.00 MHz

531 kHz to 1 602 kHz (at 9 kHz intervals)
530 kHz to 1 600 kHz (at 10 kHz intervals)

General

Power Requirements

AC 110 - 240 V , 50/60 Hz (except for Australia)
AC 240 V , 50 Hz (for Australia only)

Power Consumption

18 W (at operation) 2.0 W (in standby mode)

Dimensions (W

400 mm

85 mm

380 mm

Mass

4.3 kg

Amplifier section Front/Center/Surround

140 W per channel, RMS at 4

Ω

(Center/Surround)/ 140 W per channel, RMS at 4

Ω

(Front) at 1 kHz, with 10 % total harmonic distortion.

Subwoofer

300 W, RMS at 4

Ω

at 100 Hz, with 10 % total harmonic distortion.

Speaker section Speaker unit

25 cm Bass-reflex, Magnetically Shielded

Frequency Range

20 Hz to 200 Hz

General

Power Requirements

AC 110 V/127 V/220 - 240 V selectable with the voltage selector, 50 Hz/60 Hz

Power Consumption

170 W (at operation) 0 W (in standby mode)

Dimensions (W

D) 256 mm

482 mm

460 mm

Mass

18.5 kg

Speakers

Woofer

10.0 cm

Tweeter

4.0 cm, Bass-reflex, Magnetically Shielded

Power Handling Capacity

140 W

Impedance

Ω

Frequency Range

60 Hz to 20 kHz

Dimensions (W

250 mm

1065.5 mm

310 mm

Mass

7.2 kg

Summary of Contents for SP-PWM508


























































































Search results

Summary of Contents for SP-PWM508

Reviews:

Related manuals for SP-PWM508

Brands by name

Popular brands

JVC SP-PWM508, Service Manual

Search results

Summary of Contents for SP-PWM508

Reviews:

Related manuals for SP-PWM508

Brands by name

Popular brands