43
q
Turning On and Off the Video Output
—VIDEO POWER
On this submenu screen, you can
turn on or off the power supply
to the video output circuit built
in this unit.
7
VIDEO POWER
Turn on or off the power supply to the video output circuit.
ON :
Normally select this.
Power is supplied to the built-in video output circuit.
OFF :
Select to cut off power to the built-in video output circuit
while playing an audio source.
With this setting, interference caused by the video output
circuit will be reduced.
Note:
Even if “VIDEO POWER” is set to “OFF,” power will be supplied to
the video output circuit when on-screen display menus are used.
w
Setting the Zone 2/Speakers 2 Usage
—ZONE 2/SPEAKER 2
On this submenu, you can
determine the output signal type
through the ZONE 2 PREOUT
jacks, and the usage of the
speaker connected to the
FRONT 2/ZONE 2 SPEAKERS
terminals.
7
ZONE2PREOUT
When connecting the Zone 2 front speakers to the ZONE 2
PREOUT jacks through another amplifier (see page 19),
determine how to adjust the volume level in Zone 2.
Select one of the following:
VARIABLE :
Select when you want to adjust the Zone 2
volume level using the MASTER VOLUME
control on this unit (or /– on this
remote control).
FIX
:
Select when you want to adjust the Zone 2
volume level using the amplifier connected to
the ZONE 2 PREOUT jacks.
• The MASTER VOLUME control on this unit
(or /– on this remote control)
cannot adjust the Zone 2 volume level.
Note:
With “ZONE2PREOUT” set to “VARIABLE,” no sounds come out
of the ZONE 2 PREOUT jacks if the volume level is set to “– – –
dB.” In this case, increasing the volume level will enable the sound
output through the ZONE 2 PREOUT jacks.
7
DIGITAL OUT
Select the output digital signal format through the DIGITAL
OUT (optical) terminal on the rear.
• Each time you press the button, the output signal format
changes as follows:
THROUGH :
Select when connecting a digital signal
processor or decoder. The incoming digital
signals are transmitted through the digital output
terminal without any processing.
PCM
:
Select when connecting an MD recorder or other
digital recording device. The incoming digital
signals are down-mixed and converted into PCM
format.
p
Setting the Video Input Terminals
—VIDEO INPUT
After connecting the video
components to the video input
terminals, you have to register
which type of the terminal you
have connected to—whether the
component input or S-Video/
composite input.
Without setting this correctly,
you may not view the pictures on
the TV.
7
VIDEO INPUT
Select an appropriate input terminal used for each component—
“DVD,” “DBS,” and “VCR1.”
• Each time you press
#
(RIGHT) or
@
(LEFT), the selected
video input terminal changes as follows:
COMPO1
“
COMPO2
“
COMPO3
“
S/C
“
(back to the beginning)
Notes:
• If you have selected the same component input terminal for
different video components, only the last performed terminal
setting will be valid. (The other terminal settings will be
automatically set to “S/C.”)
• If any of “COMPO 1/2/3” is selected for the video component
which is only connected using S-video or composite video jacks
(S/C), you cannot view or record its playback picture.
VIDEO POWER
VIDEO POWER : ON
:OPERATE
:BACK
ZONE 2/SPEAKER 2
ZONE2PREOUT:VARIABLE
SPEAKER 2:SPEAKER 2
:OPERATE
:BACK
VIDEO INPUT
VIDEO DVD : COMPO1
VIDEO DBS : S/C
VIDEO VCR1 : S/C
:OPERATE
:BACK
35-44_RX-DP15B[J]f.pm6
04.3.15, 9:20 PM
43
