JVC LT-19DK8WJ Instructions Manual Download Page 13

Page: 13 / 56

Basic operations (TV)

Remote control sensor

Power lamp

MENU button

TV/AV/OK button

buttons

(Volume)

buttons

(Standby) button

Headphone jack (mini jack)

Turn the TV on from standby

mode

Press the

(Standby) button to turn

the TV on from standby mode.

When the TV is turned on, the power lamp
lights green.

To turn the TV off:

Press the

(Standby) button again. The

power lamp turns red.

• It takes approximately 5 to 8 seconds for

the TV to turn on or go into the standby

mode after the

(Standby) button on

the remote control or the

(Standby)

button on the TV is pressed.

Choose a TV channel

Press the P

buttons to choose a

programme number (Pr.)

• You can choose to change the Digital

terrestrial broadcasting (DVB-T) or
Analogue TV channels by pressing the

TV/AV/OK

button.

Watching images from

external devices

Press the TV/AV/OK button to choose
an EXT terminal.

Digital

terrestrial

broadcasting

(DVB-T)

EXT-2

Analogue

terrestrial

broadcasting

EXT-1

EXT-1

EXT-2

EXT-3

EXT-3 S-VIDEO

PC IN

EXT-3

EXT3-S

HDMI

EXT-4

TV mode

EXT modes

Summary of Contents for LT-19DK8WJ

























































Search results

Summary of Contents for LT-19DK8WJ

Reviews:

Related manuals for LT-19DK8WJ

Brands by name

Popular brands

JVC LT-19DK8WJ, Instructions Manual

Search results

Summary of Contents for LT-19DK8WJ

Reviews:

Related manuals for LT-19DK8WJ

Brands by name

Popular brands