JVC KW-XC55 Service Manual Download Page 7

Page: 7 / 59

(No.49784)1-7

3.1.6 Removing the CD mechanism assembly

(See Fig.9)

• Prior to performing the following procedures, remove the front

panel assembly, rear bracket, heat sink, top chassis assembly,
main board and CD mecha control board.

(1) Remove the three screws

attaching the CD mechanism

assembly to the top chassis assembly.

Reference:

• When attaching the CD mechanism assembly, joint the hole

of the CD mechanism assembly in boss

and boss

of the

top chassis assembly.

Fig.9

3.1.7 Removing the changer control board

(See Fig.10, 11)

• Prior to performing the following procedures, remove the front

panel assembly, rear bracket, heat sink, top chassis assembly
and bottom chassis assembly.

(1) From the back side of the bottom chassis assembly,

disconnect the card wire from the connector

CN972

on the

changer control board. (See Fig.10)

(2) From the top side of the bottom chassis assembly, remove

the two screws

attaching the changer control board. (See

Fig.11)

Reference:

• When attaching the changer control board, joint the hole of

the changer control board in joints

of the bottom chassis

assembly.

Fig.10

Fig.11

3.1.8 Removing the mecha control board

(See Fig.12 )

• Prior to performing the following procedures, remove the front

panel assembly, rear bracket, heat sink, bottom chassis
assembly and changer control board.

(1) From the back side of the bottom chassis assembly,

remove the screw

attaching the mecha control board,

and release the joints

from the bottom chassis assembly.

(2) Disconnect the wire from the connector

CJ402

and the

card wire from the connector

CN403

on the mecha control

board.

Reference:

• When attaching the mecha control board, joint the hole of

the mecha control board in joints

of the bottom chassis

assembly.

Fig.12

CD mechanism assembly

Boss

Top chassis assembly

CN972

Card wire

Changer control board

Bottom chassis assembly

Changer control board

Bottom chassis assembly

Joint

Cassette mechanism assembly

Top chassis assembly

Mecha control board

Joint

CN403

CJ402

www. xiaoyu163. com

QQ 376315150

TEL 13942296513

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Summary of Contents for KW-XC55




























































Search results

Summary of Contents for KW-XC55

Reviews:

Related manuals for KW-XC55

Brands by name

Popular brands

JVC KW-XC55, Service Manual

Search results

Summary of Contents for KW-XC55

Reviews:

Related manuals for KW-XC55

Brands by name

Popular brands