JVC KW-XC55 Service Manual Download Page 8

Page: 8 / 59

1-8 (No.49784)

3.1.9

Removing the cassette mechanism assembly
(See Fig.13)

• Prior to performing the following procedures, remove the front

panel assembly, rear bracket, heat sink, bottom chassis
assembly, changer control board and mecha control board.

(1) From the bottom side of the bottom chassis assembly,

remove the four screws

attaching the cassette

mechanism assembly to the bottom chassis assembly.

Fig.13

3.1.10 Removing the LCD board

(See Fig.14)

• Prior to performing the following procedures, remove the front

panel assembly.

(1) From the back side of front panel assembly, remove the

twelve screws

attaching the LCD board, and then turn

over the LCD board.

(2) From the reverse side of LCD board, remove the solders

from the soldered points

attaching the wire.

Fig.14

3.1.11 Removing the switch board

(See Fig.15)

• Prior to performing the following procedures, remove the front

panel assembly.

(1) From the back side of front panel assembly, remove the

five screws

attaching the switch board.

(2) Release the claws i attaching the switch board, and then

turn over the switch board.

(3) From the reverse side of switch board, remove the solders

from the soldered points

attaching the wire.

Fig.15

Cassette mechanism assembly

Bottom chassis assembly

Front panel assembly

LCD board

Solder points

Front panel assembly

Switch board

Claws

Solder points

www. xiaoyu163. com

QQ 376315150

TEL 13942296513

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Summary of Contents for KW-XC55




























































Search results

Summary of Contents for KW-XC55

Reviews:

Related manuals for KW-XC55

Brands by name

Popular brands

JVC KW-XC55, Service Manual

Search results

Summary of Contents for KW-XC55

Reviews:

Related manuals for KW-XC55

Brands by name

Popular brands