JVC KD-MX2900R Service Manual Download Page 9

Page: 9 / 86

FLOATING UNIT

DAMPER(RED)

DAMPER(BLUE)

SUSPENSION FLAME ASS'Y

DAMPER(RED)

Fig.4

FLOATING UNIT SHAFT b

DAMPER(BLUE)

SUSPENSION
FLAME ASS'Y

DAMPER(RED)

GEAR

F.A.MOTOR SA

SHAFT b

FLOATING UNIT

SUSPENSION FLAME ASS'Y

DAMPER(RED)

Fig.5

BLUE

RED

DAMPER

Fig.7

DAMPER

Fig.6

Remove the eight springs on the side of the body.
Since the springs are each different, treat them
carefully.

Turn the gear of the F.A.motor SA counterclockwise
to raise the Floating unit. Then, Shaft b is released.

Remove the three dampers. (One blue damper in
the rear of the unit, two red dampers on the left side
and the back side). Pull the tab of the damper to
release the joint as shown in the Fig.6.

NOTE-This mechanism has two kinds of damper.
So handle with care.

Remove the Floating unit upward from the
Suspension flame assembly.

Removing the Floating Unit

(see Fig.4-7)

Summary of Contents for KD-MX2900R























































































Search results

Summary of Contents for KD-MX2900R

Reviews:

Related manuals for KD-MX2900R

Brands by name

Popular brands

JVC KD-MX2900R, Service Manual

Search results

Summary of Contents for KD-MX2900R

Reviews:

Related manuals for KD-MX2900R

Brands by name

Popular brands